"s " CNS Standards List |
|
CNS 5700
2020 Edition Glossary of Terms for Rolling Bearings 滾動軸承名詞 |
|
|
|
CNS 14964-6
2020 Edition Wheelchairs − Part 6: Determination of maximum speed of electrically powered wheelchairs 輪椅－第6部：電動輪椅最大速率之測定 |
|
|
|
CNS 14668
2020 Edition Method of test for freezing point of aviation fuels(automatic phase transition method) 航空燃油凝固點相轉移自動測定法 |
|
|
|
CNS 29182-7
2020 Edition Information technology − sensor networks: Sensor Network Reference Architecture (SNRA) − Part 7: Interoperability guidelines 資訊技術－感測器網路：感測器網路參考架構(SNRA)－第7部：互運性指導綱要 |
|
|
|
CNS 11278
2020 Edition End-hardened Rails 端部熱處理鋼軌 |
|
|
|
CNS 398
2020 Edition spilt Pins 開口銷 |
|
|
|
CNS 15352
2020 Edition Hard anodic oxide coatings on aluminium and aluminium alloys 鋁及鋁合金之硬質陽極氧化膜 |
|
|
|
CNS 618
2020 Edition Method of Test for Permanent Linear Change of Refractory Brick on Reheating 耐火磚再熱線性脹縮率試驗法 |
|
|
|
CNS 4370
2020 Edition Round Thread with Clearance and Flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 3-9
2020 Edition Engineering Drawing(symbols for Hydraulic and Pneumatic Power Systems) 工程製圖（液壓系氣壓系製圖符號） |
|
|
|
CNS 4547
2020 Edition Limits of Sizes and Tolerances for ISO Metric Fine Screw Threads (Tolerance Quality: Medium,Tolerances: 6H and 6h、6g)(Diameters from 2.5 to 300mm and Pitches 0.35 to 6mm) 公制細螺紋限界尺寸及公差（ISO制）（中品級–6Ｈ、6ｈ、6ｇ）（標稱直徑2.5至300mm，螺距0.35至6mm） |
|
|
|
CNS 13158
2020 Edition Acrylonitrile-Butadiene-styrene (ABS) Plastic Pipes for Water Works 自來水用丙烯腈–丁二烯–苯乙烯（ABS）塑膠管 |
Translated |
|
|
CNS 15795
2020 Edition Information technology − Automatic identification and data capture techniques − Data Carrier Identifiers (including Symbology Identifiers) 資訊技術－自動識別與資料擷取技術－資料載體識別碼(包含符號表示法識別碼) |
|
|
|
CNS 12938
2020 Edition Vitrified clay pipes and fittings and pipe joints for drains and sewers 排水及污水用瓷化黏土管以及其配件與管接頭 |
|
|
|
CNS 62040-3
2020 Edition Uninterruptible power systems (UPS) − Part 3: Method of specifying the performance and test requirements 不斷電系統(UPS)－第3 部：性能規定法及試驗要求 |
|
|
|
CNS 15319-9-1
2020 Edition sodium hydroxide for industrial use - Part 9-1: Determination of magnesium content – Flame atomic absorption spectrometry 工業用氫氧化鈉－第９-１部：鎂含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 7818
2020 Edition Chemical Reagent (Potassium Hexachloropatiate (IV)) 化學試藥（六氯鉑酸（ＩＶ）鉀） |
|
|
|
CNS 20302
2020 Edition Health informatics − Health cards − Numbering system and registration procedure for issuer identifiers 健康資訊學－健康卡－發行者識別符之編號系統及登錄程序 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 4240
2020 Edition Electroplated Coating of Bolts, Screws and Nuts 螺栓、螺釘、螺帽之電鍍層 |
|
|
|
CNS 9677
2020 Edition Cross-Recessed (Oval) Pan Head Machine Screws 十字穴扁圓頂盤頭小螺釘 |
|
|
|
CNS 3221
2020 Edition Methods of test for Sanitary ceramic wares 衛生陶瓷器檢驗法 |
Translated |
|
|
CNS 14276
2020 Edition Electric toys − Safety 電驅動玩具安全要求 |
|
|
|
CNS 14964-22
2020 Edition Wheelchair − Part 22: set-up procedures 輪椅－第22部：設定程序 |
|
|
|
CNS 4437
2020 Edition Carbon steel tubes for machine structure 機械結構用碳鋼鋼管 |
|
|
|
CNS 15800
2020 Edition Oil of mandarin petitgrain (Citrus reticulata Blanco) 椪柑葉油 |
|
|
|
CNS 15375
2020 Edition Petroleum products - Test method for free water in liquefied petroleum gas by visual inspection 石油產品－液化石油氣游離水目視試驗法 |
|
|
|
CNS 1811
2020 Edition Mercury 化學試藥（汞） |
|
|
|
CNS 7921
2020 Edition Method of test for spices and condiments – Determination of acid-insoluble ash 香辛料及調味料之檢驗法－酸不溶性灰分之測定 |
|
|
|
CNS 4372
2020 Edition Round Thread with Clearance and steep Flank with Pitch 7mm (Limits of Sizes and Deviations--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙，深螺腹，螺距７ｍｍ之螺紋限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [92] [93] [94] [95] [96] [97] [98] |
