"It " CNS Standards List |
|
CNS 504
2017 Edition ISO Metric Fine Screw Threads (Diameters from 30 to 250 mm and PItch 3 mm) 公制細螺紋7（ISO制）（標稱直徑30至250公釐，螺距3公釐） |
|
|
|
CNS 6642
2017 Edition Calculated capacIty for unloader 卸載機之計算卸載能力 |
|
|
|
CNS 14498
2017 Edition Road Vehicle - Electrical disturbance by conduction and coupling - Part0:DefinItions and general 道路車輛-經由傳導和耦合方式的電擾動-第0部:定義及通則 |
|
|
|
CNS 12403
2017 Edition Sphere Holder and It's Accessories for Liquified Petroleum Gas 液化石油氣球型儲槽及其附屬設備 |
|
|
|
CNS 4654
2017 Edition Hexagon Set Screws wIth Full Dog Point 六角頭長柱端固定螺釘 |
|
|
|
CNS 6763
2017 Edition Parallel Shank Counterborer wIth Solid Pilot 具固定導桿之柱坑鑽（圓柱柄） |
|
|
|
CNS 6135-6
2017 Edition Hearing aids-Part6: Characteristics of electrical input circuIt for hearing aids 助聽器－第6部:電氣輸入電路的特性 |
|
|
|
CNS 11381-2
2017 Edition Glossary of Terms for ReliabilIty (Terms of Maintainability) 可靠度詞彙（有關維護度之詞彙） |
|
|
|
CNS 404
2017 Edition Symbols of SwItch Gears and Contral Gears 開關及控制設備符號 |
|
|
|
CNS 15832-2-1
2017 Edition Method of test for coating components − Part 2-1: Component analysis in solvent soluble matter − Acid value (TItrimetric method) 塗料成分試驗法－第2-1部：溶劑可溶物中成分分析－酸價(滴定法) |
|
|
|
CNS 4765
2017 Edition Method of NItric-Hydrofluoric Acid Test for Stainless Steels 不銹鋼之硝酸–氫氟酸腐蝕試驗法 |
|
|
|
CNS 141
2017 Edition Wrench, S-handle (for Pipe FItting) 彎柄雙頭扳手（用於管子） |
Translated |
|
|
CNS 9232
2017 Edition Method of Test for Dry Reed SwItches(Preparation for Delivery) 乾式簧開關檢驗法（運送準備） |
|
|
|
CNS 1194
2017 Edition Flat File for SmIth, Wide Flat End 鐵工用闊平頭扁平銼 |
Translated |
|
|
CNS 14492-3
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part3:Receivers for amplItude-modulated sound-broadcasting emissions 不同發射類別之無線電接收機的量測方法-第3部:調幅聲音廣播發射適用的接收機 |
|
|
|
CNS 12074
2017 Edition Flash CavIty of Hot Forging Closed Die 熱鍛閉合模之餘料穴 |
|
|
|
CNS 14717
2017 Edition Method for calculation of physical properties of liquefied petroleum gases from composItional analysis 液化石油氣物理性質成分分析計算法 |
|
|
|
CNS 6734
2017 Edition Disk Type Milling Cutters for Cutting Acme - Screw Threads for Threads wIth Included Angle of 30° ３０°角愛克姆螺紋銑刀 |
|
|
|
CNS 327
2017 Edition Two-way Wrench Lever wIth Elliptical Handle 兩用扳柄，橢圓形桿端 |
|
|
|
CNS 12997
2017 Edition Method of Determination for PorosIty and Uncombined Carbon of Hardmetals (Metallographic Method) 超硬合金孔隙率及游離碳測定法（金相法） |
|
|
|
CNS 7323
2017 Edition FurnIture − Domestic and kitchen storage units and kitchen-worktops − Safety requirements and test methods 家具－家用與廚房收納單元及廚房流理台 |
|
|
|
CNS 13394
2017 Edition Method of Test for ViscosIty of Pulp (Falling Ball Method) 紙漿黏度試驗法（落球法） |
Translated |
|
|
CNS 15210-6
2017 Edition Information technology - Radio frequency identification for Item management - Part 6: Parameters for air interface communications at 860MHz to 960MHz 資訊技術─品項管理之無線射頻識別─第６部：８６０ＭＨｚ至９６０ＭＨｚ空中介面通信參數 |
|
|
|
CNS 318
2017 Edition AC CircuIt Breakers (for Short Circuit Test) 交流斷路器標準（短路試驗用） |
|
|
|
CNS 10647
2017 Edition Gad, BlacksmIths' Tongs 鍛工用尖鏨平口鉗 |
|
|
|
CNS 15832-1-1
2017 Edition Method of test for coating components − Part 1-1: General rule − Common test condItions 塗料成分試驗法－第1-1部：通則－一般試驗條件 |
|
|
|
CNS 8230
2017 Edition Method of Test for Dry Reed SwItches (Insulation Resistance) 乾式簧開關檢驗法（絕緣電阻） |
|
|
|
CNS 13636
2017 Edition Steel Butt-welding Pipe FIttings 配管用鋼製對接銲接式管件 |
|
|
|
CNS 13352-2
2017 Edition Micrographics Vocabulary (Section 02: Image PosItions and Methods of Recording) 微縮技術詞彙（第二部：影像位置與縮攝方式） |
|
|
|
CNS 4365
2017 Edition Hexagon Head FItting Bolts with Short Threaded Portion 六角頭配合螺栓（具短螺紋部份） |
|
| Find out:3948Items | To Page of: First -Previous-Next -Last | [92] [93] [94] [95] [96] [97] [98] |
