"o " CNS Standards List |
|
CNS 14626
2020 Edition Cast manganese steel crossings for switch and crossing work 錳鋼岔心 |
|
|
|
CNS 5700
2020 Edition Glossary of Terms for Rolling Bearings 滾動軸承名詞 |
|
|
|
CNS 705
2020 Edition Method of Test for Volcanic Ash for General Use 火山灰（一般用）檢驗法 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 20302
2020 Edition Health informatics − Health cards − Numbering system and registration procedure for issuer identifiers 健康資訊學－健康卡－發行者識別符之編號系統及登錄程序 |
|
|
|
CNS 1220
2020 Edition Method of test for saybolt color of petroleum products (Saybolt chromometer method) 石油產品賽氏顏色試驗法(賽氏比色計法) |
|
|
|
CNS 1859
2020 Edition Phloroglucinol (1,3,5-Trihydroxybenzene) 化學試藥（１，３，５苯三酚） |
|
|
|
CNS 20005
2020 Edition Information technology − Sensor networks − Services and interfaces supporting collaborative information processing in intelligent sensor networks 資訊技術－感測器網路－智慧感測器網路中支援協作資訊處理之服務及介面 |
|
|
|
CNS 14766
2020 Edition Method of test for water and sediment in middle distillate fuels by centrifuge 蒸餾油中水分及沉澱物測定法(離心法) |
|
|
|
CNS 14506
2020 Edition Method of test for pour point of petroleum products (automatic ressure pulsing method) 石油產品流動點測定法(自動壓力脈衝法) |
|
|
|
CNS 4370
2020 Edition Round Thread with Clearance and Flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 3-9
2020 Edition Engineering Drawing(Symbols for Hydraulic and Pneumatic Power Systems) 工程製圖（液壓系氣壓系製圖符號） |
|
|
|
CNS 15317-3
2020 Edition Crosslinked polyethylene (PE-X) pipe for hot and cold water conveyance - Part 3: Fittings 冷熱水輸送用交連聚乙烯管－第３部：管件 |
|
|
|
CNS 9075
2020 Edition Retaining rings-uniform section C type Ｃ型同心扣環 |
|
|
|
CNS 4240
2020 Edition Electroplated Coating of Bolts, Screws and Nuts 螺栓、螺釘、螺帽之電鍍層 |
|
|
|
CNS 4372
2020 Edition Round Thread with Clearance and Steep Flank with Pitch 7mm (Limits of Sizes and Deviations--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙，深螺腹，螺距７ｍｍ之螺紋限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 157
2020 Edition Square Taper Washers (for I Sections) 方形推拔墊圈（工字鐵用） |
|
|
|
CNS 15284
2020 Edition Rims for truck and bus 卡車及大客車用輪圈 |
|
|
|
CNS 15820-2
2020 Edition Electric motorcycles − Safety specifications − Part 2: Protection against hydrogen hazards for motorcycles fuelled with compressed hydrogen 電動機車－安全規範－第2 部：防止氫氣危害 |
|
|
|
CNS 5270-2
2020 Edition Graphical Symbols for Fluid Power Diagrams-Pump and Motor 液壓、氣壓圖形符號–泵及馬達 |
|
|
|
CNS 3590
2020 Edition Method of Test for Normal Consisteney of Hydraulic Cement 水硬性水泥之正常稠度檢驗法 |
|
|
|
CNS 8988
2020 Edition Chemical Reagent(Dry Loss Determination) 化學試藥（乾失量測定） |
|
|
|
CNS 785
2020 Edition Method of Test for Time of Setting of Hydraulic Cement (by Gilmore Needle) 水硬性水泥凝結時間檢驗法（吉爾摩氏針法） |
|
|
|
CNS 15566-3
2020 Edition Safety of machinery – Pressure-sensitive protective devices – Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices 機械安全－壓敏保護裝置－第3 部：設計及測試壓敏緩衝器、板、線及類似裝置之一般原則 |
|
|
|
CNS 3221
2020 Edition Methods of test for Sanitary ceramic wares 衛生陶瓷器檢驗法 |
Translated |
|
|
CNS 1524
2020 Edition Acetone (Reagent) 化學試藥（丙酮） |
|
|
|
CNS 10895
2020 Edition Vocabulary of metrology − Basic and general concepts and associated terms (VIM) 計量學詞彙－基本與一般概念及相關用語 |
|
|
|
CNS 6906
2020 Edition Cable Terminals of Storage Battery for Automobiles (Type BA) 汽車用蓄電池板製電線端子（ＢＡ型） |
|
|
|
CNS 5286
2020 Edition Industrial automation systems and integration - Numerical control of machines - Coordinate system and motion nomenclature 工業自動化系統與整合－數值控制機器之坐標系統及運動術語 |
|
|
|
CNS 15823
2020 Edition Measurement of antibacterial activity on plastics and other non-porous surfaces 塑膠及非多孔表面抗菌性測定法 |
|
| Find out:15086Items | To Page of: First -Previous-Next -Last | [86] [87] [88] [89] [90] [91] [92] |
