"f " CNS Standards List| Method test | Corrosion metals | Tolerances Rolling | Identification Cards | Accuracy Inspection | Glossary Terms | Oils sassafras | Face Face | |
|
CNS 15319-6
2020 Edition Sodium hydroxide for industrial use - Part 6: Determination of iron content - Atomic absorption spectrometry and inductively coupled plasma optical emission spectrophotometry 工業用氫氧化鈉－第６部：鐵含量測定法－原子吸收光譜及感應耦合電漿發光光譜分析法 |
|
|
|
CNS 9250
2020 Edition fork Lift Trucks 叉舉車 |
|
|
|
CNS 1890
2020 Edition Potassium humate fertilizer 氫氧化鉀 (試藥) |
|
|
|
CNS 15319-9-1
2020 Edition Sodium hydroxide for industrial use - Part 9-1: Determination of magnesium content – Flame atomic absorption spectrometry 工業用氫氧化鈉－第９-１部：鎂含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 1964
2020 Edition Sodium fluoride 化學試藥（氟化鈉） |
|
|
|
CNS 4532
2020 Edition Terms Relating to the End (Point) of Fasteners 結件端部詞彙 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 1671
2020 Edition Copper (Ⅱ) Sulfate Pentahydrate (Reagent) 化學試藥（五水合硫酸銅（Ⅱ）） |
|
|
|
CNS 147
2020 Edition Cylindrical Shaft End (for Assembling Coupling, Pulley and Gear) 柱軸梢（用以承裝聯軸器，皮帶輪與齒輪） |
|
|
|
CNS 14177
2020 Edition Quality management systems － Guidelines for quality plans 品質管理系統－品質計畫指導綱要 |
|
|
|
CNS 5270-8
2020 Edition Graphical Symbols for Fluid Power Diagrams-Check Valve 液壓、氣壓圖形符號–止回閥 |
|
|
|
CNS 5092
2020 Edition Symbols for Indication Appearing on Machine Tools 工具機操作符號–動作件運動方向符號 |
Translated |
|
|
CNS 2010
2020 Edition Sulfurous Acid 化學試藥（亞硫酸） |
|
|
|
CNS 2248
2020 Edition Method of Test for Heat of Hydration of Hydraulic Cement 水硬性水泥水合熱試驗法 |
Translated |
|
|
CNS 11740
2020 Edition Method of Test for Crushing Strength of Insulating Fire Bricks 絕熱耐火磚抗碎強度試驗法 |
|
|
|
CNS 4370
2020 Edition Round Thread with Clearance and flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 12843
2020 Edition Chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布 |
Translated |
|
|
CNS 15415
2020 Edition Gymnastic equipment − General safety requirements and test methods 體操設備－一般安全要求及試驗法 |
|
|
|
CNS 7559
2020 Edition Basic Dimensions of Copper Alloy Pipe Flanges 銅合金製管凸緣基準尺度 |
|
|
|
CNS 12508
2020 Edition General rules for ion-selective electrode method 離子選擇電極測定法通則 |
|
|
|
CNS 7593
2020 Edition Helical Springs Made of Round Wire Dimensions for Cold Coiled Compression Springs of Less Than 0.5 mm Wire Diameter 冷捲成形壓縮螺旋彈簧（簧線直徑小於０．５ｍｍ之構造尺度） |
|
|
|
CNS 7680
2020 Edition Shapes and Dimensions of Seats for Buses 大客車用座椅之形狀及尺度 |
|
|
|
CNS 15284
2020 Edition Rims for truck and bus 卡車及大客車用輪圈 |
|
|
|
CNS 7534
2020 Edition Personal protective equipment for work positioning and prevention of falls from a height − Belts for work positioning and restraint and work positioning lanyards 工作定位及防止由高處墜落之個人防護具－工作定位與限制帶及工作定位索 |
|
|
|
CNS 11908
2020 Edition Plastic Bobbins for Ring Spinning Flame 低壓電表用塑膠箱體及固定板 |
|
|
|
CNS 156
2020 Edition Square Taper Washers (for Channels) 方形推拔墊圈（槽鐵用） |
|
|
|
CNS 15271
2020 Edition Oil of eucalyptus citriodora Hook. 檸檬桉油 |
|
|
|
CNS 7890
2020 Edition Window Weather Strips for Buses 大客車用車窗防風雨橡膠鑲條 |
|
|
|
CNS 16142
2020 Edition Balancing of rotating tools and tool systems 旋轉刀具及刀具系統之平衡調校 |
|
|
|
CNS 14561
2020 Edition Method of test for determination of bezene and toluene in finished motor and aviation gasoline by gas chromatography 車用及航空汽油中苯及甲苯含量測定法（氣體層析法） |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [82] [83] [84] [85] [86] [87] [88] |
