"D " CNS Standards List |
|
CNS 531
2020 Edition Iso Metric Screw ThreaDs-Tolerances-Deviations for Constructional Threads 公制螺紋公差（ＩＳＯ制）（結構用螺紋之偏差） |
Translated |
|
|
CNS 1858
2020 Edition PhenylsemicarbaziDe 化學試藥（苯基胺脲） |
|
|
|
CNS 60669-2-1
2020 Edition Switches for householD and similar fixed electrical installations − Part 2-1: Particular requirements − Electronic switches 家用和類似用途固定式電氣裝置之開關－第2-1 部：電子式開關之個別要求 |
|
|
|
CNS 14809
2020 Edition GuiDelines for auditing management systems 管理系統稽核指導綱要 |
|
|
|
CNS 15259
2020 Edition Oil of lavanDin abrial (Lavandula angustifolia Miller × Lavandula latifolia Medikus), French type 阿拉伯混種薰衣草油（法國） |
|
|
|
CNS 786
2020 Edition MethoD of Test for Time of Setting of Hydraulic Cement (by Vicat Needle) 水硬性水泥凝結時間檢驗法（費開氏針法） |
|
|
|
CNS 15789
2020 Edition Robots anD robotic devices – Safety requirements for personal care robots 機器人及機器人裝置－人員照護機器人之安全要求 |
|
|
|
CNS 15193-3
2020 Edition Safety of machinery - Permanent means of access to machinery - Part 3: Stairs,steplaDders and guard-rail 機械安全－接近機械之永久性方法－第３部：階梯、踏梯及護欄 |
|
|
|
CNS 3586
2020 Edition Perlite Heat Insulating Sheet (Block) anD Pipe 真珠岩保溫板（磚）及保溫管 |
Translated |
|
|
CNS 15353-1
2020 Edition Test methoDs for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart scale method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第１部：圖表比例尺法 |
|
|
|
CNS 154
2020 Edition Large UnfinisheD Washers (for Metric Bolts and Nuts: M6 - M52) 粗製大墊圈（用於公制螺栓及螺帽Ｍ６至Ｍ５２） |
Translated |
|
|
CNS 15200-5-3
2020 Edition MethoDs of test for paints – Part 5-3: Mechanical property of film – Impact resistance test 塗料一般試驗法－第５－３部：塗膜機械性質：衝擊試驗 |
|
|
|
CNS 14964-6
2020 Edition Wheelchairs − Part 6: Determination of maximum speed of electrically powered wheelchairs 輪椅－第6部：電動輪椅最大速率之測定 |
|
|
|
CNS 15272
2020 Edition Oil of ylang-ylang〔Cananga oDorata (Lamark) J.D.Hooker and Thomson〕 伊蘭伊蘭油 |
|
|
|
CNS 4836
2020 Edition EDible palm oil 食用棕櫚油 |
|
|
|
CNS 15817
2020 Edition EDible camellia seed oil 食用苦茶油(油茶油) |
|
|
|
CNS 14718
2020 Edition MethoD of test for hydrogen sulfide in liquefied petroleum (LP) gases (lead acetate method) 液化石油氣硫化氫試驗法（醋酸鉛法） |
|
|
|
CNS 15566-3
2020 Edition Safety of machinery – Pressure-sensitive protective Devices – Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices 機械安全－壓敏保護裝置－第3 部：設計及測試壓敏緩衝器、板、線及類似裝置之一般原則 |
|
|
|
CNS 14596
2020 Edition WelDing consumables − Gas shielded and self-shielded flux cored wires for arc welding of mild steel, high strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用 鋼氣遮護及自遮護電弧銲接用包藥銲線 |
|
|
|
CNS 3384
2020 Edition MethoD of test for foaming characteristics of lubricating oils 潤滑油起泡性試驗法 |
|
|
|
CNS 1865
2020 Edition Phosphorus PentoxiDe 化學試藥（五氧化二磷） |
|
|
|
CNS 15423-1
2020 Edition Equipment for water supply service – Part 1: Test methoDs of hydrostatic pressure 自來水用器具－第1部：耐壓試驗法 |
|
|
|
CNS 9445-1
2020 Edition Sampling proceDures for inspection by variables − Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL 計量值檢驗抽樣程序－第1部：單一品質特性與單一允收品質界限(AQL)逐批檢驗依AQL檢索之單次抽樣計畫 |
|
|
|
CNS 14579-2
2020 Edition MethoD of test for prevention of fire for automobiles – Part 2: In the event of collision for passenger cars 汽車火災預防檢驗法－第２部：小客車碰撞 |
|
|
|
CNS 5814
2020 Edition Rubber compounDing ingredients − Carbon black − Determination of loss on heating 橡膠配合劑－碳黑－加熱減量(熱失量)之測定 |
|
|
|
CNS 15787
2020 Edition MethoD of fillet weld test for welding consumables 銲接材料之填角銲試驗法 |
|
|
|
CNS 61850-5
2020 Edition Communication networks anD systems for power utility automation − Part 5: Communication requirements for functions and device models 電力公用事業自動化之通訊網路及系統－第5部：功能及裝置模型之通訊要求事項 |
|
|
|
CNS 62498-3
2020 Edition Railway applications − Environmental conDitions for equipment − Part 3: Equipment for signalling and telecommunications 鐵路應用－設備之環境條件－第3部：號誌及電訊設備 |
|
|
|
CNS 16130-2
2020 Edition Machine tools − Environmental evaluation of machine tools − Part 2: MethoDs for measuring energy supplied to machine tools and machine tool components 工具機—工具機之環境評估—第2部：供應至工具機及工具機構件能量之量測方法 |
|
|
|
CNS 8411-2
2020 Edition Test methoDs for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Abrasive jet test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－第２部：噴射磨耗試驗法 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [74] [75] [76] [77] [78] [79] [80] |
