"P " CNS Standards List |
|
CNS 15200-5-4
2020 Edition Methods of test for Paints – Part 5-4: Mechanical property of film – Scratch hardness (Pencil method) 塗料一般試驗法－第５－４部：塗膜機械性質：刮痕硬度（鉛筆法） |
|
|
|
CNS 12616
2020 Edition Method of Test for Electrical Conductivity of Aviation and Distillate Fuels Containing a Static DissiPator Additive 航空燃油含靜電逸散劑導電度測定法 |
|
|
|
CNS 14103-3
2020 Edition Prosthetics and orthotics - Vocabulary - Part 2: Terms relating to external limb prostheses and wearers of these prostheses 義肢學與矯具學－詞彙－第３部：外用矯具之術語 |
|
|
|
CNS 14104-2
2020 Edition Prosthetics and orthotics - Limb deficiencies - Part 1: Method of describing limb deficiencies present at birth 義肢學與矯具學－肢體缺陷－第２部：下肢截肢之描述 |
|
|
|
CNS 1887
2020 Edition Potassium Fluoride(Reagent) 六氰鐵（Ⅲ）酸鉀（試藥） |
|
|
|
CNS 62040-3
2020 Edition UninterruPtible power systems (UPS) − Part 3: Method of specifying the performance and test requirements 不斷電系統(UPS)－第3 部：性能規定法及試驗要求 |
|
|
|
CNS 12617
2020 Edition Method of Test for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) 航空燃油熱氧化穩定性試驗法（ＪＦＴＯＴ程序） |
|
|
|
CNS 5818
2020 Edition Rubber comPounding ingredients − Carbon black − Determination of iodine adsorption number 橡膠配合劑－碳黑－碘吸附值之測定 |
|
|
|
CNS 14506
2020 Edition Method of test for Pour point of petroleum products (automatic ressure pulsing method) 石油產品流動點測定法(自動壓力脈衝法) |
|
|
|
CNS 62282-3-201
2020 Edition Fuel cell technologies − Part 3-201: Stationary fuel cell power systems − Performance test methods for small fuel cell power systems 燃料電池技術－第3-201部：定置型燃料電池發電系統－小型燃料電池發電系統之性能試驗法 |
|
|
|
CNS 14490-2
2020 Edition Robots and robotic devices − Safety requirements for industrial robots − Part 2: Robot systems and integration 機器人及機器人裝置－工業機器人之安全要求－第2 部：機器人系統及整合 |
|
|
|
CNS 14293
2020 Edition Pyrogallol Pyrogallic Acid 1,2,3-Trihydroxybenzene 實驗室用參考示溫錐 |
|
|
|
CNS 7024
2020 Edition Cable Terminals for Automobiles (TyPe CA) 汽車用電線端子（塞型陽端子） |
|
|
|
CNS 7593
2020 Edition Helical SPrings Made of Round Wire Dimensions for Cold Coiled Compression Springs of Less Than 0.5 mm Wire Diameter 冷捲成形壓縮螺旋彈簧（簧線直徑小於０．５ｍｍ之構造尺度） |
|
|
|
CNS 3-18
2020 Edition Engineering drawing (Symbolic Presentation and indication of adhesive, fold and pressed joints) 工程製圖（板金膠合、鉤合、壓合符號表示法） |
|
|
|
CNS 5270
2020 Edition Basic GraPhical Symbols for Fluid Power Diagrams 液壓、氣壓圖形符號–基本符號 |
Translated |
|
|
CNS 15278
2020 Edition Oil of lemongrass [CymboPogon flexuosus (Nees ex Steudel) J.F. Watson] 檸檬草油 |
|
|
|
CNS 13158
2020 Edition Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipes for Water Works 自來水用丙烯腈–丁二烯–苯乙烯（ABS）塑膠管 |
Translated |
|
|
CNS 7680
2020 Edition ShaPes and Dimensions of Seats for Buses 大客車用座椅之形狀及尺度 |
|
|
|
CNS 622
2020 Edition Method of SPalling Test for Refractory Bricks Under Sudden Change of Temperature 耐火磚之急熱急冷試驗法 |
|
|
|
CNS 15820-2
2020 Edition Electric motorcycles − Safety sPecifications − Part 2: Protection against hydrogen hazards for motorcycles fuelled with compressed hydrogen 電動機車－安全規範－第2 部：防止氫氣危害 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 60669-2-6
2020 Edition Switches for household and similar fixed electrical installations – Part 2-6: Particular requirements – Fireman's switches for exterior and interior signs and luminaires 家用和類似用途固定式電氣裝置之開關－第2-6 部：外部與內部標誌及燈具用消防員開關之個別要求 |
|
|
|
CNS 5817
2020 Edition Rubber comPounding ingredients − Carbon black − Determination of pellet size distribution 橡膠配合劑－碳黑－粒徑分布之測定 |
|
|
|
CNS 9557
2020 Edition Round-steel link chains for general Purposes and hoisting equipments, chain in fixed length, short linked 一般目的及起重設備用圓鋼製短環環鏈及定長環鏈 |
|
|
|
CNS 15319-8-1
2020 Edition Sodium hydroxide for industrial use - Part 8-1: Determination of calcium content - Flame atomic absorption spectrometry 工業用氫氧化鈉－第８-１部：鈣含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 9747
2020 Edition Method of Test for Fineness of Portland Cement by the Turbidimeter 卜特蘭水泥細度檢驗法（濁度計法） |
|
|
|
CNS 19086-2
2020 Edition Information technology − Cloud comPuting − Service level agreement (SLA) framework − Part 2: Metric model 資訊技術－雲端運算－服務水準協議(SLA)框架－第2部：度量模型 |
|
|
|
CNS 7029
2020 Edition ShaPe, Dimensions and Travel Angles of Drawbar Eyes for Full Trailers 全拖車用拖桿環首之形狀、尺度及活動範圍 |
|
|
|
CNS 4544
2020 Edition Limits of sizes and tolerances for ISO metric coarse screw threads (Tolerance quality: medium, tolerances: 5 H、6 H and 6 h、6 g)(Diameters from 1 to 68 mm and Pitches 0.25 to 6 mm) 公制粗螺紋限界尺寸及公差（ＩＳＯ制）（中品級–5Ｈ、6Ｈ、6ｈ、6ｇ）（標稱直徑1至68mm，螺距0.25至6mm） |
|
| Find out:11004Items | To Page of: First -Previous-Next -Last | [66] [67] [68] [69] [70] [71] [72] |
