"P " CNS Standards List |
|
CNS 4240
2020 Edition ElectroPlated Coating of Bolts, Screws and Nuts 螺栓、螺釘、螺帽之電鍍層 |
|
|
|
CNS 15389
2020 Edition Leather - Physical and mechanical tests - Determination of tear load - Double edge tear 皮革－物性及機械性質測試－雙邊撕裂強度試驗法 |
|
|
|
CNS 612
2020 Edition ShaPe and Dimension of Refractory Bricks 耐火磚之形狀及尺度 |
|
|
|
CNS 1851
2020 Edition Phenol (Reagent) 酚（試藥） |
|
|
|
CNS 1897
2020 Edition Potassium Oxalate 過氯酸鉀（試藥） |
|
|
|
CNS 80000-7
2020 Edition Quantities and units – Part 7: Light and radiation 量及單位－第7部：光與輻射 |
|
|
|
CNS 6921
2020 Edition Rubber handlebar griP for bicycle 自行車用橡膠握套 |
|
|
|
CNS 3-11
2020 Edition Engineering drawings (RePresentation of diagrams) 工程製圖（圖表畫法） |
|
|
|
CNS 14143
2020 Edition Methods of chemical analysis for fine silicon carbide Powders for fine ceramics 精密陶瓷用碳化矽微末化學分析法 |
|
|
|
CNS 12617
2020 Edition Method of Test for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure) 航空燃油熱氧化穩定性試驗法（ＪＦＴＯＴ程序） |
|
|
|
CNS 9558
2020 Edition Round-steel link chains for hoisting equiPments, calibrated, tested, short linked 起重設備用圓鋼製短環環鏈 |
|
|
|
CNS 4670-20
2020 Edition SPecified Items for Machine Tools - Gear Shapers (Pinion Cutter Type) 工具機規範之項目–齒輪刨製機（齒輪刨刀型） |
|
|
|
CNS 15319-8-2
2020 Edition Sodium hydroxide for industrial use - Part 8-2: Determination of calcium content – Inductively coupled plasma optical emission spectrophotometry 工業用氫氧化鈉－第８-２部：鈣含量測定法－感應耦合電漿發光光譜分析法 |
|
|
|
CNS 399
2020 Edition Fastening of TaPer Pins and Cotter Pins 定位銷裝配位置（用於圓錐銷及開口銷） |
|
|
|
CNS 7298
2020 Edition Method of test for water absorPtiveness of paper and board − Cobb method 紙及紙板吸水度試驗法－Cobb法 |
|
|
|
CNS 11425
2020 Edition Method of Test for Cone Penetration of Refractory Mortar 耐火墁料針入度試驗法 |
|
|
|
CNS 1887
2020 Edition Potassium Fluoride(Reagent) 六氰鐵（Ⅲ）酸鉀（試藥） |
|
|
|
CNS 30128
2020 Edition Information technology − Sensor networks − Generic sensor network aPplication interface 資訊技術－感測器網路－ 通用感測器網路應用介面 |
|
|
|
CNS 2519
2020 Edition Railway SleePer (for 1067 mm Gauge) 鐵路木枕（軌距1067mm者） |
|
|
|
CNS 8408-2
2020 Edition Accelerated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 618
2020 Edition Method of Test for Permanent Linear Change of Refractory Brick on Reheating 耐火磚再熱線性脹縮率試驗法 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoPlastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 14294
2020 Edition Method for determination of resistance to sulfuric acid of dense shaPed refractory products 緻密定型耐火製品抗硫酸性測定法 |
|
|
|
CNS 15200-5-6
2020 Edition Methods of test for Paints – Part 5–6: Mechanical property of film - Adhesion test (Cross–cut test) 塗料一般試驗法－第５－６部：塗膜機械性質：附著試驗(方格法) |
|
|
|
CNS 3589
2020 Edition Air-Entraining Additions for Use in The Manufacture of Air-Entraining Portland Cement 輸氣卜特蘭水泥製造用輸氣添加劑 |
|
|
|
CNS 7557
2020 Edition SliP-on Welding Steel Pipe Flanges (30 kgf/㎠) 滑入熔接式鋼製管凸緣（30 kgf/㎠） |
|
|
|
CNS 16129-2
2020 Edition Railway aPplications − Welding of railway vehicles and components − Part 2: Quality requirements and certification of welding manufacturer 鐵路應用－鐵路車輛及其零組件之銲接－第2部：銲接製造廠商品質要求及驗證 |
|
|
|
CNS 27
2020 Edition Transmission EquiPment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 12615
2020 Edition Method of Test for Oxidation Stability of Aviation Fuels (Potential Residue Method) 航空燃油氧化穩定性試驗法（潛在殘餘物法） |
|
|
|
CNS 17296-3
2020 Edition Additive manufacturing − General Principles − Part 3: Main characteristics and corresponding test methods 積層製造－通則－第3部：主要特性及對應試驗法 |
|
| Find out:11004Items | To Page of: First -Previous-Next -Last | [65] [66] [67] [68] [69] [70] [71] |
