CNS Standards Solution | HOME | LOGIN | SIGN UP | CONTACT US | 中文版 |
�� ��

Chinese National Standards
中華民國國家標準
- Taiwan 台灣 -
 

"Ho " CNS Standards List

K-Chemical Industry
CNS 9893    2019 Edition
Testing metHods for rubber vibration isolators
隔振橡膠試驗法
C-Electrical Engineering
CNS 60670-1    2019 Edition
Boxes and enclosures for electrical accessories for Household and similar fixed electrical installations − Part 1: General requirements
家用及類似用途固定安裝電氣配件用箱體及外殼-第1部:一般要求
K-Chemical Industry
CNS 14432-2    2019 Edition
Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions − MetHod by analysis of evolved carbon dioxide − Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test
塑膠材料在控制堆肥條件下最終好氧生物分解度測定法-二氧化碳釋出量分析法-第2部:實驗室規模重量測定法
Z2-Industry Safety
CNS 16105    2019 Edition
Protective clothing − Electrostatic properties − Part 3: Test metHods for measurement of charge decay
防護服-化學防護-防護服材料耐液體及氣體滲透性試驗
Z7-General & Miscellaneous
CNS 15755-13-2    2019 Edition
Conversion tables − Part 13-2: Heat transfer − Watt per square meter kelvin and kilocalorie per Hour square meter degree Celsius
單位換算表-第13-2 部:熱傳遞-瓦特每平方公尺克耳文與千卡每小時平方公尺攝氏溫度
Z2-Industry Safety
CNS 16121-1    2019 Edition
Electrical apparatus for the detection of combustible gases in domestic premises − Part 1: Test metHods and performance requirements
家居處所可燃氣體偵測用之電氣裝備-第1部:試驗方法及性能要求
K-Chemical Industry
CNS 15123    2019 Edition
Paints and varnishes - Determination of total lead - Flame atomic absorption spectrometric metHod
塗料-總鉛測定-火焰原子吸收光譜法
R-Ceramic Industry
CNS 7529    2019 Edition
MetHod for sampling of abrasive grains
磨料採樣法
C-Electrical Engineering
CNS 13306-1-4    2019 Edition
Specification for radio disturbance and immunity measuring apparatus and metHods - Part 1-4: Radio disturbance and immunity measuring apparatus - Ancillary equipment - Radiated disturbances
射頻擾動和免疫力量測設備與量測方法-第1-4部:射頻擾動和免疫力量測設備-輔助設備-輻射擾動
B-Mechanical Engineering
CNS 16107-1    2019 Edition
Hollow taper interface with flange contact surface − Part 1: Shanks − Dimensions
具凸緣接觸面之空心錐度界面-第1部:刀柄尺度
L-Textile Industry
CNS 15103    2019 Edition
Textiles - Determination of abrasion resistance of fabrics by the Martindale metHod - Part 1 : Martindale abrasion testing apparatus
紡織品耐摩損性馬丁代爾試驗法-第1部:馬丁代爾耐摩損試驗機
N-Agriculture, Food
CNS 12900    2019 Edition
MetHod of Test for Fertilizers:Neubauer Test on Crop Injury
肥料檢驗法(作物毒害試驗)
H-Non-ferrous Materials & Metallurgy
CNS 14896-8    2019 Edition
Titanium and titanium alloys - MetHods for determination of hydrogen content
鈦及鈦合金-氫定量法
D-Automotive & Aircraft Engineering
CNS 8678    2019 Edition
MetHod of Service Brake Road Test for Truck and Bus
貨車、大客車常用煞車─路段試驗法
D-Automotive & Aircraft Engineering
CNS 2744    2019 Edition
MetHod of Disassembly Inspection for Automobiles
汽車分解檢查方法
H-Non-ferrous Materials & Metallurgy
CNS 12907    2019 Edition
MetHods of Test for Iron in Nickel Materials for Electron Tubes
電子管用鎳材料中鐵檢驗法
C-Electrical Engineering
CNS 13059-4    2019 Edition
PHotovoltaic devices - Part 4: Reference solar devices - Procedures for establishing calibration traceability
太陽光電裝置-第4部:基準太陽 裝置-建立校正追溯性之程序
X-Information & Communication
CNS 15157    2019 Edition
Dynamic Host configuration protocol for IPv6 (DHCPv6)
用於網際網路協定第6版之動態主機組態協定
H-Non-ferrous Materials & Metallurgy
CNS 15228-4    2019 Edition
Test metHods for lead-free solders - Part 4: Solderbility test by a wetting balance method
無鉛銲錫試驗法-第4部:沾錫性試驗-潤濕平衡法
B-Mechanical Engineering
CNS 15660-2    2019 Edition
Test conditions for numerically controlled turning machines and turning centres − Part 2: Geometric tests for machines with a vertical workHolding spindle
數值控制車床及車削中心機之試驗條件- 第2部:立式工件夾持主軸工具機之幾何試驗
A-Civil Engineering & Architecture
CNS 13976    2019 Edition
MetHod of test for flexural strength of dimensional stone
石材彎曲強度試驗法
N-Agriculture, Food
CNS 13280    2019 Edition
MetHod of Test for Hazardous Components in Sulfate Fertilizers (Determination of Sulfurous Acid Content)
肥料中有害成分檢驗法(亞硫酸之測定)
K-Chemical Industry
CNS 14297    2019 Edition
MetHod for determination of MTBE, ETBE, TAME, DIPE, tertiary-amyl alcohol and C₁ to C₄ alcohols in gasoline − Gas chromatography
汽油中醚類與醇類試驗法-氣相層析法
G-Ferrous Materials & Metallurgy
CNS 2908    2019 Edition
MetHod of macro-streak-flaw test for steel
鋼料條痕缺陷目視試驗法
C-Electrical Engineering
CNS 14545-9    2019 Edition
Fire hazard testing-Part 2:Test metHods-Section 3:Bad-connection test with heaters
火災危險性試驗-第2部:試驗方法-第3章:不良連接試驗(電熱法)
N-Agriculture, Food
CNS 11132    2019 Edition
MetHod of Test for Feed Additives: Determination of Enramycin
飼料添加物檢驗法–恩黴素之測定
D-Automotive & Aircraft Engineering
CNS 9596    2019 Edition
MetHod of Test of Strength for Automobile Suspension Springs
汽車用懸吊彈簧強度檢驗法
D-Automotive & Aircraft Engineering
CNS 12173    2019 Edition
Test metHod for brake linings compressibility strain of automobiles
汽車用煞車軔襯壓縮應變試驗法
L-Textile Industry
CNS 13756    2019 Edition
MetHods of Test for Man-made Staple Fibers
人造棉狀纖維試驗法
C-Electrical Engineering
CNS 13059-7    2019 Edition
PHotovoltaic devices - Part 7: Computation of the spectral mismatch correction for measurements of photovoltaic devices
太陽光電裝置-第7部:太陽光電裝置量測之光譜不匹配修正計算

Find out:5568Items   |  To Page of: First -Previous-Next -Last  | [55] [56] [57] [58] [59] [60] [61]

 

| HOME | LOGIN | SIGN UP | CONTACT US | 中文版 | ©  CNS-standards.org Copyright  2001-2025 All Rights Reserved
The authority agency link :
Bureau of Standards, Metrology & Inspection M.O.E.A.
This site is not affiliated with or endorsed by the BSMI or MOEA.