"D " CNS Standards List| Method Test | Gypsum Plaster | Method stability | Method test | Marine Cast | Method Test | Sodium Sulfite, | Light Type | |
|
CNS 5285
1984 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5284
1984 Edition ADdendum Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 11158
1984 Edition Tungsten-CarbiDe Bits and Rod for Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
|
|
|
CNS 11159
1984 Edition Tungsten-CarbiDe Tip Core Drills 碳化鎢鑽刃留心鑽頭 |
|
|
|
CNS 6415
1984 Edition Series of moDules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 6412
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 6411
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 6410
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 6409
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Material Factor Zм 圓柱齒輪與傘齒輪之負載能力計算－材料因數ＺM |
|
|
|
CNS 11157
1984 Edition Lubrication Holes, Grooves anD Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 6408
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算－齒廓面作用帶因數Ｚ H |
|
|
|
CNS 6414
1984 Edition Basic Rack of Straight Bevel Gears for General anD Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 4729
1984 Edition RounD Nuts 圓螺帽 |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics MoulDings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 6407
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 4658
1984 Edition Tommy Screws with FixeD Clamping Bolt 貫頭螺釘（固定扳桿型） |
|
|
|
CNS 4660
1984 Edition Tommy Nuts with FixeD Clamping Bolt 貫頭螺帽（固定扳桿型） |
|
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics MoulDings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 4663
1984 Edition CloseD Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽（片封式，嵌於塑膠製品內） |
|
|
|
CNS 5280
1984 Edition Helix Angles for CylinDrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 5283
1984 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 4732
1984 Edition KnurleD Nuts with Ring 有環滾紋螺帽 |
|
|
|
CNS 11151
1984 Edition MethoD of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 11154
1984 Edition Grease Guns-Rush Type HanD Guns 手用衝壓式黃油槍 |
|
|
|
CNS 11153
1984 Edition MethoD of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 11155
1984 Edition Grease Guns-Lever Type HanD Guns 手用槓壓式黃油槍及附件 |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 3094
1984 Edition SoliD Punches 衝頭 |
|
|
|
CNS 11072
1984 Edition MethoD of X-Ray Fluorescence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 2521
1984 Edition LaminateD Aluminium Foils 貼合積層鋁箔 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [419] [420] [421] [422] [423] [424] [425] |
