"D " CNS Standards List |
|
CNS 6410
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics MoulDings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 9705
1984 Edition General Rules for Emission-Spectroscopic Analysis of Iron anD Steel 鐵及鋼之發光光譜分析法通則 |
|
|
|
CNS 5283
1984 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 10006
1984 Edition MethoD for Photoelectric Emission Spectrochemical Analysis of Iron And Steel 鐵及鋼之光電式發光光譜分析法 |
|
|
|
CNS 4658
1984 Edition Tommy Screws with FixeD Clamping Bolt 貫頭螺釘（固定扳桿型） |
|
|
|
CNS 4660
1984 Edition Tommy Nuts with FixeD Clamping Bolt 貫頭螺帽（固定扳桿型） |
|
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics MoulDings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 6415
1984 Edition Series of moDules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 4664
1984 Edition CloseD Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 4732
1984 Edition KnurleD Nuts with Ring 有環滾紋螺帽 |
|
|
|
CNS 10502
1984 Edition MethoD for X-Ray Fluorescence Spectrometric Analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 10503
1984 Edition Emission-Spectroscopic Analysis for Pig Iron anD Cast Iron 生鐵及鑄鐵之發光光譜分析法 |
|
|
|
CNS 6414
1984 Edition Basic Rack of Straight Bevel Gears for General anD Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 6412
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 6411
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 4729
1984 Edition RounD Nuts 圓螺帽 |
|
|
|
CNS 4731
1984 Edition KnurleD Nuts for Drawing Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 4663
1984 Edition CloseD Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽（片封式，嵌於塑膠製品內） |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 5267
1984 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 5268
1984 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 5277
1984 Edition CylinDrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 5280
1984 Edition Helix Angles for CylinDrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 11112
1984 Edition MethoDs of Chemical Analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 11151
1984 Edition MethoD of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 11153
1984 Edition MethoD of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 11155
1984 Edition Grease Guns-Lever Type HanD Guns 手用槓壓式黃油槍及附件 |
|
|
|
CNS 11070
1984 Edition General Rules of Determination for Carbon in Metallic Materials 金屬材料中碳定量法通則 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [418] [419] [420] [421] [422] [423] [424] |
