"LE " CNS Standards List| Basic Environmental | Marine Recessed | Method Species | Single Action | Hard Lead | Folding tables | Micrographic Vocabulary | Flat Taper | |
|
CNS 15374
2020 Edition Liquefied petroLEum gases - Determination of dissolved residues (High-temperature gas chromatographic method) 液化石油氣－可溶殘餘物測定法（高溫氣相層析法） |
|
|
|
CNS 9446
2020 Edition Steel drums - Non-removabLE head 鋼製圓桶－密蓋式 |
|
|
|
CNS 11771
2020 Edition General RuLEs for Allowance of Chemical Analysis and Physical Test 化學分析及物理試驗許可差總則 |
|
|
|
CNS 12616
2020 Edition Method of Test for ELEctrical Conductivity of Aviation and Distillate Fuels Containing a Static Dissipator Additive 航空燃油含靜電逸散劑導電度測定法 |
|
|
|
CNS 16144-1
2020 Edition Gas detectors − ELEctrical apparatus for the detection of carbon monoxide in domestic premises − Part 1: Test methods and performance requirements 氣體偵測器－家居處所一氧化碳偵測用之電氣裝備－第1部：試驗方法及性能要求 |
|
|
|
CNS 8734
2020 Edition Spices and condiments − Chillies and capsicums, whoLE or ground (powdered) 香辛料及調味料－全果狀或粉狀番椒與辣椒 |
|
|
|
CNS 11418
2020 Edition Non-Metallic Protecting Tubes for ThermocoupLEs 熱電偶用非金屬保護管 |
|
|
|
CNS 3126
2020 Edition Bolts, Screws and Studs-Nominal LEngths, and Thread Lengths 螺栓、螺釘、螺樁之長度及螺紋長度 |
|
|
|
CNS 3-4
2020 Edition Engineering drawings - Geometrical toLErancing 工程製圖(幾何公差) |
|
|
|
CNS 3542
2020 Edition Forged shackLEs for general lifting purposes – Dee shackles and bow shackles 一般起重吊掛用鍛造鉤環－D形鉤環及弓形鉤環 |
|
|
|
CNS 4372
2020 Edition Round Thread with CLEarance and Steep Flank with Pitch 7mm (Limits of Sizes and Deviations--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙，深螺腹，螺距７ｍｍ之螺紋限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 6907
2020 Edition CabLE Terminals of Storage Battery for Automobiles (Type BB) 汽車用蓄電池管製電線端子（ＢＢ型） |
|
|
|
CNS 785
2020 Edition Method of Test for Time of Setting of Hydraulic Cement (by Gilmore NeedLE) 水硬性水泥凝結時間檢驗法（吉爾摩氏針法） |
|
|
|
CNS 7971
2020 Edition Tyre Valve Core Housing and Spuds for AutomobiLEs 汽車輪胎氣門嘴心子外殼及固定座 |
|
|
|
CNS 15375
2020 Edition PetroLEum products - Test method for free water in liquefied petroleum gas by visual inspection 石油產品－液化石油氣游離水目視試驗法 |
|
|
|
CNS 4545
2020 Edition Limits of Sizes and ToLErances for ISO Metric Coarse Screw Threads (Tolerance Quality: Coarse,Tolerances: 7H and 8g)(Diameters from 3 to 68mm and Pitches 0.5 to 6mm) 公制粗螺紋限界尺寸及公差（ISO制）（粗品級–7H、8g）（標稱直徑3至68mm，螺距0.5至6mm） |
|
|
|
CNS 15389
2020 Edition LEather - Physical and mechanical tests - Determination of tear load - Double edge tear 皮革－物性及機械性質測試－雙邊撕裂強度試驗法 |
|
|
|
CNS 52901
2020 Edition Additive manufacturing − General principLEs − Requirements for purchased AM parts 積層製造－ 通則－ 積層製造之零組件的採購要求 |
|
|
|
CNS 8408-2
2020 Edition AcceLErated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 7975
2020 Edition Tyre Valve Washers and Grommets for AutomobiLEs 汽車輪胎氣門嘴墊圈與套環 |
|
|
|
CNS 1220
2020 Edition Method of test for saybolt color of petroLEum products (Saybolt chromometer method) 石油產品賽氏顏色試驗法(賽氏比色計法) |
|
|
|
CNS 5561
2020 Edition Ignition Coils for AutomobiLEs 汽車用點火線圈 |
Translated |
|
|
CNS 6324
2020 Edition Switches of Back-up Lamps for AutomobiLEs 汽車倒車燈開關 |
|
|
|
CNS 1963
2020 Edition Sodium EthyLEnediamine Tetraacetate 化學試藥（四乙酸乙二胺鈉） |
|
|
|
CNS 12704
2020 Edition Method of Test for ParticLE Size Distribution of Alumina or Quartz Using Centrifugal Sedimentation 氧化鋁或石英粒度分布測定法（離心沈積法） |
|
|
|
CNS 15232
2020 Edition Oils of LEmon and petitgrain citronnier, and oil of lime obtained by a mechanical process - Determination of citral (neral + geranial) content (Gas chromatographic method on capillary columns) 機械程序製檸檬油、檸檬葉油及萊姆油－檸檬油醛（橙花醛＋香葉草醛）含量測定法（毛細管柱氣相層析法） |
|
|
|
CNS 4245
2020 Edition CLEarance Holes for Metric Bolts (1.6 up to and Including 150 mm Thread Diameter) 穿通孔徑（螺紋直徑1.6公釐~150公釐） |
|
|
|
CNS 14667
2020 Edition Method of test for pour point of petroLEum products(automatic tilt method) 石油產品流動點試驗法（自動傾斜法） |
|
|
|
CNS 7973
2020 Edition Tyre Valve Cores for AutomobiLEs 汽車輪胎氣門嘴心子 |
|
|
|
CNS 15566-3
2020 Edition Safety of machinery – Pressure-sensitive protective devices – Part 3: General principLEs for design and testing of pressure-sensitive bumpers, plates, wires and similar devices 機械安全－壓敏保護裝置－第3 部：設計及測試壓敏緩衝器、板、線及類似裝置之一般原則 |
|
| Find out:6143Items | To Page of: First -Previous-Next -Last | [37] [38] [39] [40] [41] [42] [43] |
