"3 3 " CNS Standards List| Geometrical Product | Crimming Tools | Quality Requirement | Method Test | Hose Clamps | Methods Vibration | Wheelchairs − | Diving suits | |
|
CNS 331
2020 Edition Hand-Wheels with Crooked Rims and Straight Arms 手輪（曲環，直輻） |
|
|
|
CNS 15319-4
2020 Edition Sodium hydroxide for industrial use - Part 4: Determination of sodium sulfate content 工業用氫氧化鈉－第４部：硫酸鈉含量測定法 |
|
|
|
CNS 1903
2020 Edition Potassium Phosphate, Monobasic Potassium Biphosphate Soerenson's Potassium Phosphate 化學試藥（玫瑰紅酸鉀） |
|
|
|
CNS 15200-4-3
2020 Edition Methods of test for paints - Part 4-3: Visual characteristics of film - Colorimetry (Principles) 塗料一般試驗法－第４－３部：塗膜視覺特性－測色（原理） |
|
|
|
CNS 2038
2020 Edition Xylene (Xylol) 化學試藥（二甲苯） |
|
|
|
CNS 13531
2020 Edition Glossary Cones 圓錐用語 |
|
|
|
CNS 13626
2020 Edition Steel drums - Removable head (open head) 鋼製圓桶－掀蓋式 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 3220-3
2020 Edition Sanitary ceramic ware- Washbasin 衛生陶瓷器—洗面盆 |
Translated |
|
|
CNS 4370
2020 Edition Round Thread with Clearance and Flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 15319-6
2020 Edition Sodium hydroxide for industrial use - Part 6: Determination of iron content - Atomic absorption spectrometry and inductively coupled plasma optical emission spectrophotometry 工業用氫氧化鈉－第６部：鐵含量測定法－原子吸收光譜及感應耦合電漿發光光譜分析法 |
|
|
|
CNS 4318
2020 Edition ISO Miniature Screw Threads-Tolerances 公制精細小螺紋公差（ＩＳＯ制） |
Translated |
|
|
CNS 9343
2020 Edition Hand Platform Truck 手推平車 |
|
|
|
CNS 1853
2020 Edition Phenol red (Reagent) 酚紅（試藥） |
|
|
|
CNS 7593
2020 Edition Helical Springs Made of Round Wire Dimensions for Cold Coiled Compression Springs of Less Than 0.5 mm Wire Diameter 冷捲成形壓縮螺旋彈簧（簧線直徑小於０．５ｍｍ之構造尺度） |
|
|
|
CNS 15423-2
2020 Edition Equipment for water supply service– Part 2: Test methods of low temperature resistant 自來水用器具－第2部：耐寒試驗法 |
|
|
|
CNS 7534
2020 Edition Personal protective equipment for work positioning and prevention of falls from a height − Belts for work positioning and restraint and work positioning lanyards 工作定位及防止由高處墜落之個人防護具－工作定位與限制帶及工作定位索 |
|
|
|
CNS 4235
2020 Edition Fasteners－Acceptance inspection 結件之允收檢驗 |
|
|
|
CNS 9380
2020 Edition Lead Wires for Automobiles Electrical Equipments 汽車用電裝備之附屬導線 |
|
|
|
CNS 3389
2020 Edition Method for Calculating Viscosity Index from Kinematic Viscosity at 40 and 100 Degree C 由40°及100℃動黏度計算黏度指數之方法 |
|
|
|
CNS 14389
2020 Edition Methods of measuring for specific surface area of fine ceramic powders by gas adsorption 精密陶瓷粉體BET氣體吸附比表面積測定法 |
|
|
|
CNS 12843
2020 Edition Chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布 |
Translated |
|
|
CNS 9173
2020 Edition Gas-Filled Single Tube Shock Absorbers for Automobiles 汽車用單管充氣減震器 |
Translated |
|
|
CNS 7973
2020 Edition Tyre Valve Cores for Automobiles 汽車輪胎氣門嘴心子 |
|
|
|
CNS 4354
2020 Edition Finishes and tolerances for product grade of screws and nuts 螺釘與螺帽之加工精度及公差（特精級） |
|
|
|
CNS 8483
2020 Edition Control Cables for Motor - Cycle 兩輪機車用操縱線 |
Translated |
|
|
CNS 13534
2020 Edition System of Cone Tolerances 圓錐公差制度 |
|
|
|
CNS 3-3
2020 Edition Engineering Drawing (Method of indicating surface texture on drawings) 工程製圖(表面織構符號) |
|
|
|
CNS 9352
2020 Edition Bushes for Plain Bearings Made From Dura Plastics 滑動軸承軸襯–熱硬性樹脂製 |
|
|
|
CNS 15345-2
2020 Edition Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedure 機械安全－降低由機械釋放有害性物質對健康造成之風險－第２部：查證程序之方法 |
|
| Find out:6360Items | To Page of: First -Previous-Next -Last | [36] [37] [38] [39] [40] [41] [42] |
