"M " CNS Standards List |
|
CNS 11153
1984 Edition Method of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 10761
1984 Edition Method of Test for Surface Wax on Waxed Paper or Paperboard 蠟紙及蠟紙板之表面蠟量試驗法 |
Translated |
|
|
CNS 1419
1984 Edition Method of Test for Acetone 丙酮檢驗法 |
|
|
|
CNS 9705
1984 Edition General Rules for EMission-Spectroscopic Analysis of Iron and Steel 鐵及鋼之發光光譜分析法通則 |
|
|
|
CNS 10993
1984 Edition Methods of Testing Preformed Expansion Joint Fillers for Concrete (Nonextruding and Resilient Types) 混凝土伸縮縫預製填縫物試驗法（凹式） |
|
|
|
CNS 11014
1984 Edition Methods of Determination for Manganese in Iron and Steel 鋼鐵中錳定量法 |
|
|
|
CNS 10735
1984 Edition Plastic RiMs for Bicycles 平車或跑車型自行車塑膠輪圈 |
|
|
|
CNS 10795
1984 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計（發電機式） |
|
|
|
CNS 10503
1984 Edition EMission-Spectroscopic Analysis for Pig Iron and Cast Iron 生鐵及鑄鐵之發光光譜分析法 |
|
|
|
CNS 10502
1984 Edition Method for X-Ray Fluorescence Spectrometric Analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 11156
1984 Edition Grease Guns-DiMensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 5022
1984 Edition Thyristorstack for Welding Machine 電焊機用閘流調節器 |
Translated |
|
|
CNS 5027
1984 Edition Control TiMers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 5026
1984 Edition Welding TransforMers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 5268
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of CoMposite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of CuMulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 5279
1984 Edition DiMensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 5282
1984 Edition Basic Rack of Gear-Cutting Tools for Involute Tooth SysteM 漸開線齒制用切齒刀具之基準齒條 |
|
|
|
CNS 5284
1984 Edition AddenduM Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 2388
1984 Edition Method of Test for Combustion Rate of Cigarette Paper 捲菸紙燃燒率試驗法 |
Translated |
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 4731
1984 Edition Knurled Nuts for Drawing InstruMents 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 6415
1984 Edition Series of Modules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 5266
1984 Edition Series of Modules for Worm Gear Pairs 齒輪模數（蝸桿蝸輪對） |
|
|
|
CNS 5028
1984 Edition Rectifier Type DC Arc Welding Machines with Drooping Characteristic 穩流整流式直流電弧電焊機 |
|
|
|
CNS 5030
1984 Edition Projection Welding Machine 凸壓電焊機 |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [396] [397] [398] [399] [400] [401] [402] |
