"f " CNS Standards List |
|
CNS 12070
1987 Edition Ejectorplate Guide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 12072
1987 Edition Locating Pin of Die Casting Molds 壓鑄模用定位銷 |
|
|
|
CNS 12071
1987 Edition Angle Pin of Die Casting Molds 壓鑄模用斜角撐銷 |
|
|
|
CNS 12077
1987 Edition Minimum Rounded Radii and Drafts of Hot Forging Closed Die 熱鍛閉合模之最小圓角半徑與拔模斜度(角度) |
|
|
|
CNS 12083
1987 Edition Method of Test for Fiber Optic Devices (FOPT-33 Fiber Optic Cable Tensile Loading and Bending Test) 光纖裝置檢驗法（光纜拉力負載與彎曲試驗FOTP-33） |
|
|
|
CNS 12106
1987 Edition Method of Test for Water Absorbency of Bibulous Paper -- Absorption Rate Method 高吸水性紙吸水性試驗法－吸水速率法 |
Translated |
|
|
CNS 12087
1987 Edition Method of Test for Fiber Optic Devices (FOPT-82 Fluid Penetration Test for Filled Fiber Optic Cable) 光纖裝置檢驗法（充膠光纜流體滲透試驗FOTP-82） |
|
|
|
CNS 12086
1987 Edition Method of Test for Fiber Optic Devices (FOPT-55 Method for Measuring the Coating Geometry of Optical Fibers) 光纖裝置檢驗法（光纖鍍層幾何形狀之測量法FOTP-55） |
|
|
|
CNS 8230
1987 Edition Method of Test for Dry Reed Switches (Insulation Resistance) 乾式簧開關檢驗法（絕緣電阻） |
|
|
|
CNS 8229
1987 Edition Method of Test For Dry Reed Switches (Operate, Bounce, Release and Transfer (SPDT) Time) 乾式簧開關檢驗法（動作、彈跳、復原與轉接時間） |
|
|
|
CNS 8228
1987 Edition Method of Test for Dry Reed Switches (Dielectric) 乾式簧開關檢驗法（電介質） |
|
|
|
CNS 12085
1987 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求FOTP-54） |
|
|
|
CNS 7663
1987 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 24 Maintenance Aging Test) 頻率3 MHz以下電連接器檢驗法(維護老化試驗TP-24) |
|
|
|
CNS 8227
1987 Edition Method of Test for Dry Reed Switches (Operation Parameters) 乾式簧開關檢驗法（動作參數） |
|
|
|
CNS 7661
1987 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 22 Life Test) 頻率3 MHz以下電連接器檢驗法（壽命試驗TP-22） |
|
|
|
CNS 8226
1987 Edition Method of Test for Dry Reed Switches (Visual and Mechanical Inspection) 乾式簧開關檢驗法（目視與機械檢驗） |
|
|
|
CNS 12082
1987 Edition Method of Test for Fiber Optic Devices (FOPT-30 Frequency Domain Measurement of Multimode Optical Fiber Information Transmission Capacity) 光纖裝置檢驗法（多模光纖資訊傳輸量之頻域測量FOTP-30） |
|
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (Quality Control and Quality Assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 8224
1987 Edition Method of Test for Dry Reed Switches (General Rules) 乾式簧開關檢驗法（總則） |
|
|
|
CNS 12081
1987 Edition Method of Test for Fiber Optic Devices (FOPT-13 Visual and Mechanical Inspection of Fibers,Cables,Connectors and Other Fiber Optic Devices) 光纖裝置檢驗法（光纖、光纜、連接器及其他光纖裝置之目視及機械檢查FOTP-13） |
|
|
|
CNS 7642
1987 Edition Method of Test for Fiber Optic Devices (Air Leakage Testing of Fiber Optic Component Seals) 光纖裝置檢驗法(光纖組件密封漏氣試驗FOTP-23) |
|
|
|
CNS 11938
1987 Edition Sprue Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 12084
1987 Edition Method of Test for Fiber Optic Devices (FOPT-36 Twist Test for Fiber Optic Cable Assemblies 光纖裝置檢驗法（光纜組件扭力試驗FOTP-36） |
|
|
|
CNS 11874
1987 Edition fixed Mica Capacitors ( Type CM 35 ) 雲母固定電容器(CM35型) |
|
|
|
CNS 11902
1987 Edition Method of Test for Fiber Optic Devices (FOTP-52 Temperature Dependence of Attenuation for Optical Fibers) 光纖裝置檢驗法（溫度變化對光纖衰減之影響FOTP-52） |
|
|
|
CNS 11940
1987 Edition Standard Parts of Injection Mold 塑膠型模形狀及其標準組件 |
|
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 9229
1987 Edition Method of Test for Dry Reed Switches (Lead Finish and Terminal Strength) 乾式簧開關檢驗法（引線表面處理與端子強度） |
|
|
|
CNS 11932
1987 Edition Angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [395] [396] [397] [398] [399] [400] [401] |
