"M " CNS Standards List |
|
CNS 4300
1985 Edition Test Code for Accuracy of Surface Grinding Machines With Horizontal Grinding Wheel Spindle and Reciprocating Table 往復床台型臥式平面磨床精度檢驗標準 |
Translated |
|
|
CNS 3994
1985 Edition High Voltage CoMbination Starters 高壓綜合型起動盤 |
|
|
|
CNS 3095
1985 Edition Center Punches (9.5Mm) 9.5 mm中心衝 |
|
|
|
CNS 8195
1985 Edition Method of Test for Subplate Type Solenoid Operated 4 - Port Valves (Oil - Hydraulic Use ) 液壓用副板型四通電磁操作閥檢驗法 |
|
|
|
CNS 3563
1985 Edition Method of Test for Low Elongation Stress of Vulcanized Rubber 硫化橡膠低伸長應力試驗法 |
|
|
|
CNS 11377
1985 Edition Magnetic Particle Test for Castings and Forgings 鑄件及鍛件磁粒檢驗法 |
Translated |
|
|
CNS 11400
1985 Edition Method of Eddy Current Test for Metal Bars Rods and Wires 金屬棒桿及線渦電流檢驗法 |
|
|
|
CNS 11399
1985 Edition Method of Straight-Beam Ultrasonic Test for Steel Plate for Pressure Vessel Use 壓力容器用鋼板直束法超音波檢驗法 |
|
|
|
CNS 11353
1985 Edition Methods of Measurement for Light Source Colour 光源色之測定方法 |
|
|
|
CNS 6554
1985 Edition General Rules for EnaMeled Copper Wires 漆包銅線總則 |
Translated |
|
|
CNS 11352
1985 Edition Method of Comparison for Surface Colour 表面色之比較方法 |
|
|
|
CNS 11351
1985 Edition Methods of Measurement for Colour of Reflecting of Transmitting Objects 物體色之測定方法 |
|
|
|
CNS 10864
1984 Edition Method of Test for Hypo Number of Pulp 紙漿海波值試驗法 |
Translated |
|
|
CNS 5279
1984 Edition DiMensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 11156
1984 Edition Grease Guns-DiMensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒(空)主要尺寸 |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪(齒跨距測量工具之徑向調整量數值表) |
|
|
|
CNS 10993
1984 Edition Methods of Testing Preformed Expansion Joint Fillers for Concrete (Nonextruding and Resilient Types) 混凝土伸縮縫預製填縫物試驗法(凹式) |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪(因數COSα/ COSαω數值表) |
|
|
|
CNS 10911
1984 Edition Method of Test for Microswitches 微動開關試驗法 |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪(齒跨距數值表) |
|
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪(齒跨距數值表) |
|
|
|
CNS 9705
1984 Edition General Rules for EMission-Spectroscopic Analysis of Iron and Steel 鐵及鋼之發光光譜分析法通則 |
|
|
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of CuMulative Circular Pitch 圓柱齒輪輪齒之精度(累積周節誤差之公差) |
|
|
|
CNS 11014
1984 Edition Methods of Determination for Manganese in Iron and Steel 鋼鐵中錳定量法 |
|
|
|
CNS 4659
1984 Edition ToMmy Screws with Movable Clamping Bolt 貫頭螺釘(滑動扳桿型) |
|
|
|
CNS 5298
1984 Edition Hose ClaMps for the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽(長型封閉式,嵌於塑膠製品與壓鑄件內用) |
|
|
|
CNS 4664
1984 Edition Closed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽(封閉式,嵌於塑膠製品內) |
Translated |
|
|
CNS 4663
1984 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽(片封式,嵌於塑膠製品內) |
|
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽(嵌於塑膠製品內) |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [395] [396] [397] [398] [399] [400] [401] |



