CNS Standards Solution | HOME | LOGIN | SIGN UP | CONTACT US | 中文版 |
�� ��

Chinese National Standards
中華民國國家標準
- Taiwan 台灣 -
 

"f " CNS Standards List

A-Civil Engineering & Architecture
CNS 8757    1987 Edition
Method of Test for Bulk Specific Gravity and Density of Compacted Bituminous Mixtyres Using Paraffin- Coated Specimens
瀝青混合料壓實試體容積比重及密度試檢驗法(封臘法)
C-Electrical Engineering
CNS 8672    1987 Edition
Method of Test for Dry Reed Switches(Carry Current)
乾式簧開關檢驗法(負載電流)
B-Mechanical Engineering
CNS 5988    1987 Edition
Stud Shanks for Press Dies
衝模用栓柄
C-Electrical Engineering
CNS 8229    1987 Edition
Method of Test For Dry Reed Switches (Operate, Bounce, Release and Transfer (SPDT) Time)
乾式簧開關檢驗法(動作、彈跳、復原與轉接時間)
C-Electrical Engineering
CNS 8222    1987 Edition
Method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 40 Crush Test)
頻率3 MHz以下電連接器檢驗法(軋壓試驗TP-40)
C-Electrical Engineering
CNS 8670    1987 Edition
Method of Test for Dry Reed Switches(Seals)
乾式簧開關檢驗法(密封)
C-Electrical Engineering
CNS 8669    1987 Edition
Method of Test for Dry Reed Switches(Shock)
乾式簧開關檢驗法(衝擊)
C-Electrical Engineering
CNS 8668    1987 Edition
Method of Test for Dry Reed Switches(Vibration)
乾式簧開關檢驗法(振動)
C-Electrical Engineering
CNS 8667    1987 Edition
Method of Test for Dry Reed Switches(Internal Moisture)
乾式簧開關檢驗法(內部潮濕)
C-Electrical Engineering
CNS 5550    1987 Edition
Method of Test for Thermistor
熱敏電阻器檢驗法
C-Electrical Engineering
CNS 5535    1987 Edition
Small Switch for Single-phase Motors
單相電動機用小型開關

Translated
C-Electrical Engineering
CNS 8230    1987 Edition
Method of Test for Dry Reed Switches (Insulation Resistance)
乾式簧開關檢驗法(絕緣電阻)
C-Electrical Engineering
CNS 8228    1987 Edition
Method of Test for Dry Reed Switches (Dielectric)
乾式簧開關檢驗法(電介質)
B-Mechanical Engineering
CNS 5987    1987 Edition
Shanks of Press Die
衝模柄
B-Mechanical Engineering
CNS 5993    1987 Edition
Coil Springs for Press Dies
衝模用螺旋彈簧
B-Mechanical Engineering
CNS 5992    1987 Edition
Knockout Equipment for Press Dies
衝模用頂出裝置
B-Mechanical Engineering
CNS 11893    1987 Edition
Shears for Hedge Trimming
手剪(修剪樹籬用)
B-Mechanical Engineering
CNS 5991    1987 Edition
Round Punches for Press Dies
衝模用圓衝頭
B-Mechanical Engineering
CNS 5990    1987 Edition
Die Sets for Press Dies
衝模用模座組
B-Mechanical Engineering
CNS 11892    1987 Edition
Shears for Flower and Grass Cutting
手剪(修剪花草用)
C-Electrical Engineering
CNS 11878    1987 Edition
Method of Test for R.F Booster
射頻信號增幅器檢驗法
C-Electrical Engineering
CNS 8224    1987 Edition
Method of Test for Dry Reed Switches (General Rules)
乾式簧開關檢驗法(總則)
C-Electrical Engineering
CNS 11874    1987 Edition
fixed Mica Capacitors ( Type CM 35 )
雲母固定電容器(CM35型)
C-Electrical Engineering
CNS 8223    1987 Edition
Method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 41 Circular Jacket Cable Flexing Test)
頻率3 MHz以下電連接器檢驗法(圓形護套電纜可撓性試驗TP-41)
C-Electrical Engineering
CNS 12007    1987 Edition
Method of Test for Helical Scanning Video Tape Recorders
螺線掃描錄放影機檢驗法
B-Mechanical Engineering
CNS 11870    1987 Edition
Method of Test for Refrigerant Compressors
冷媒壓縮機試驗法
G-Ferrous Materials & Metallurgy
CNS 11836    1987 Edition
Glossary of Terms Used in Iron and Steel (Products and Quality)
鋼鐵詞彙(製品及品質)
G-Ferrous Materials & Metallurgy
CNS 11835    1987 Edition
Glossary of Terms Used in Heat Treatment of Iron and Steel
鋼鐵熱處理詞彙
C-Electrical Engineering
CNS 11830    1987 Edition
Measuring Methods for Light Emitting Diodes (for Indication)
發光二極體(指示用)測量法
C-Electrical Engineering
CNS 11829    1987 Edition
Light Emitting Diodes (for Indication)
發光二極體(指示用)

Find out:12815Items   |  To Page of: First -Previous-Next -Last  | [394] [395] [396] [397] [398] [399] [400]

 

| HOME | LOGIN | SIGN UP | CONTACT US | 中文版 | ©  CNS-standards.org Copyright  2001-2025 All Rights Reserved
The authority agency link :
Bureau of Standards, Metrology & Inspection M.O.E.A.
This site is not affiliated with or endorsed by the BSMI or MOEA.