"M " CNS Standards List |
|
CNS 10926
1987 Edition Method of Test for Fiber Optic Devices (FOTP-27 Measuring Outside (Uncoated) Diameter of Optical Fibers) 光纖裝置檢驗法（無外被光纖外徑測量法FOTP-27） |
|
|
|
CNS 11875
1987 Edition Fixed Mica Capacitors (Type CM 50) 雲母固定電容器(CM50型) |
|
|
|
CNS 11904
1987 Edition Method of Test for Fiber Optic Devices (FOTP-81 Compound Flow (Drip) Test for Filled Fiber Optic Cable) 光纖裝置檢驗法（有填充物光纜之化合物滴漏試驗FOTP-81） |
|
|
|
CNS 11939
1987 Edition Setting Plugs of Molds for Plastics 塑膠型模用定位塞 |
|
|
|
CNS 11901
1987 Edition DiMensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 11900
1987 Edition Fixed CeraMic Capacitors for Electronic Equipment (Semiconductor) 電子設備用陶瓷固定電容器（半導體） |
Translated |
|
|
CNS 11898
1987 Edition Reliability Assured Plastic FilM Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 8227
1987 Edition Method of Test for Dry Reed Switches (Operation Parameters) 乾式簧開關檢驗法（動作參數） |
|
|
|
CNS 4700
1987 Edition Hexagon Head Bolts with Thread ApproxiMately to Head and with Small Widths Across Flats 六角頭全螺紋螺栓（具小對面寬度） |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 9097
1987 Edition TherMostats ( Pressure Type ) 恆溫器（壓力式） |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for Plastics 塑膠型模用止銷 |
|
|
|
CNS 11902
1987 Edition Method of Test for Fiber Optic Devices (FOTP-52 Temperature Dependence of Attenuation for Optical Fibers) 光纖裝置檢驗法（溫度變化對光纖衰減之影響FOTP-52） |
|
|
|
CNS 11938
1987 Edition Sprue Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 5770
1987 Edition General Specification for TherMistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 11940
1987 Edition Standard Parts of Injection Mold 塑膠型模形狀及其標準組件 |
|
|
|
CNS 11895
1987 Edition General Rules for Reliability Assured Fixed Mica Capacitors 可靠度保證雲母固定電容器總則 |
|
|
|
CNS 11992
1987 Edition Method of Test for Fiber Optic Devices (FOTP-42 Optical Crosstalk in Fiber Optic Components) 光纖裝置檢驗法（光纖零組件內之串訊FOTP-42） |
|
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 8228
1987 Edition Method of Test for Dry Reed Switches (Dielectric) 乾式簧開關檢驗法（電介質） |
|
|
|
CNS 10872
1987 Edition Method of Test for Fiber Optic Devices (FOTP-2 Impact Test) 光纖裝置檢驗法(撞擊試驗FOTP-2) |
|
|
|
CNS 11934
1987 Edition Stop Bolts of Molds for plastics 塑膠型模用止動螺栓 |
|
|
|
CNS 11893
1987 Edition Shears for Hedge TriMming 手剪（修剪樹籬用） |
|
|
|
CNS 11937
1987 Edition Runner Pull Pins of Molds for Plastics 塑膠型模用流道拉銷 |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
|
|
CNS 11905
1987 Edition Method of Test for Fiber Optic Devices (FOTP-83 Cable to Interconnecting Device Axial Compressive Loading) 光纖裝置檢驗法（光纜至連接器之軸向壓力負載FOTP-83） |
|
|
|
CNS 7664
1987 Edition Method of Test for Low Frequency (Below 3 MHz)Electrical Connectors (TP - 25 Probe Damage Test) 頻率3 MHz以下電連接器檢驗法(探針損壞試驗TP-25) |
|
|
|
CNS 9229
1987 Edition Method of Test for Dry Reed Switches (Lead Finish and Terminal Strength) 乾式簧開關檢驗法（引線表面處理與端子強度） |
|
|
|
CNS 9231
1987 Edition Method of Test for Dry Reed Switches(Physical Dimensions) 乾式簧開關檢驗法（實體尺度） |
|
|
|
CNS 4374
1987 Edition Wing Nuts ( SMall Type ) 翼形螺帽（低型） |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [388] [389] [390] [391] [392] [393] [394] |
