"f " CNS Standards List |
|
CNS 10579
1994 Edition Method of Test for Surface Strength of Paper and Paperboard (IGT Tester) 紙及紙板表面強度試驗法(IGT試驗機) |
![]() Translated |
|
|
CNS 10692
1994 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Introduction) 陸上行動通信用25-94 MHz調頻/調相接收機檢驗法(總則) |
![]() |
|
|
CNS 10693
1994 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Definition and Test Condition) 陸上行動通信用25-947 MHz調頻/調相接收機檢驗法(定義、試驗條件) |
![]() |
|
|
CNS 8695
1994 Edition Hard Drawn Steel Wires for Prestressed Concrete 預力混凝土用硬鋼線 |
![]() |
|
|
CNS 11211
1994 Edition Method of Test for Freeness of Pulp (Canadian Standard Freeness Method) 紙漿游離度試驗法(加拿大標準游離度法) |
![]() Translated |
|
|
CNS 10694
1994 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Characteristics of the Measuring Equipment and Reference Sensitivity) 陸上行動通信用25-947 MHz調頻/調相接收機檢驗法(測量設備之特性及基準靈敏度) |
![]() |
|
|
CNS 10695
1994 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用25-947 MHz調頻/調相接收機檢驗法(聲頻響應、諧波失真因數、交流聲及雜訊) |
![]() |
|
|
CNS 11622
1994 Edition Method of Test for Fiber Length of Pulp by Projection 紙漿纖維長度投影試驗法 |
![]() |
|
|
CNS 10540
1994 Edition Test Code for Performance of Wood Milling Machines 木工銑床動態檢驗法 |
![]() |
|
|
CNS 7149
1994 Edition Steel Castings for Low Temperature and High Pressure Service 低溫高壓用鑄鋼件 |
![]() |
|
|
CNS 13378
1994 Edition Boron Steel Wires for Cold Heading and Cold Forging 冷打及冷鍛用硼鋼鋼線 |
![]() |
|
|
CNS 13377
1994 Edition Boron Steel Wire Rods for Cold Heading and Cold Forging 冷打及冷鍛用硼鋼線料 |
![]() |
|
|
CNS 4967
1994 Edition Groove Cutters for Wookworking Machines 木工機械用開槽圓鋸片 |
![]() |
|
|
CNS 13374
1994 Edition Tolerances, Allowable Deviations and Permissible Wears of Limit Gauges 限界量規之公差、許可差及容許磨耗 |
![]() |
|
|
CNS 4809
1994 Edition General Rules for Accuracy Inspection of Woodworking Machines 木工機械精度檢驗通則 |
![]() |
|
|
CNS 13343
1994 Edition Oil Tempered Chromium Silicon Alloy Steel Wires for Springs 彈簧用油回火矽鉻合金鋼鋼線 |
![]() |
|
|
CNS 7995
1994 Edition Oil Tempered Carbon Steel Wires for Valve Springs 閥彈簧用油回火碳鋼鋼線 |
![]() |
|
|
CNS 287
1994 Edition Method of Test for Chemical Analysis of Limes 石灰化學分析法 |
![]() |
|
|
CNS 4589
1994 Edition General Rules of Fixed Capacitors for Use in Electronic Equipment 電子設備用固定電容器通則 |
![]() |
|
|
CNS 13375
1994 Edition Gauge Blanks for Screw Thread Limit Gauges 螺紋限界量規之形狀及尺度 |
![]() |
|
|
CNS 7479
1994 Edition Oil Tempered Silicon Manganese Alloy Steel Wires for Springs 彈簧用油回火矽錳合金鋼鋼線 |
![]() |
|
|
CNS 13245
1994 Edition Method of Test for Rubber Condoms 乳膠製衛生套檢驗法 |
![]() Translated |
|
|
CNS 13393
1994 Edition Method of Test for Relative Viscosity of Pulp (Oken Viscometer Method) 紙漿相對黏度試驗法(王研法) |
![]() Translated |
|
|
CNS 4901
1994 Edition General Rules for Reliability Assured Electronic Components 可靠度保證電子零組件通則 |
![]() |
|
|
CNS 12211
1994 Edition Environmental Requirements for Electronic Components 電子零組件環境條件之分類 |
![]() |
|
|
CNS 5176
1994 Edition Method of Determination for Wire Side and Felt Side of Paper 紙張網面與毯面測定法 |
![]() Translated |
|
|
CNS 4813
1994 Edition Planer Knives for Woodworking Machines 木工機械用平鉋刀 |
![]() |
|
|
CNS 2862
1994 Edition Deep Groove Ball Bearings: Single - Row Without filling Notch 徑向深溝滾珠軸承(單列、無填裝槽) |
![]() Translated |
|
|
CNS 7143
1994 Edition Steel Castings for Welded Structure 銲接結構用鑄鋼件 |
![]() |
|
|
CNS 7145
1994 Edition High Tensile Strength Carbon Steel Castings and Low Alloy Steel Castings for Structural Purposes 結構用高強度碳鋼及低合金鋼鑄鋼件 |
![]() |
Find out:12815Items | To Page of: First -Previous-Next -Last | [373] [374] [375] [376] [377] [378] [379] |