"S " CNS Standards List| Methods determination | Method test | Method test | Implementation Requirement | Method test | Sealing reagent | Identification cards | Tolerance Whitworth | |
|
CNS 4419
2017 Edition CounterSunk Square Bolts with Square Short Squore 平頂埋頭短方頸螺栓 |
|
|
|
CNS 7049
2017 Edition Method of TeSt for Carbon Blank in Olefin Plastics 烯烴類塑膠中碳黑含量檢驗法 |
|
|
|
CNS 2520
2017 Edition FerrophoSphorus 磷鐵 |
|
|
|
CNS 12479
2017 Edition MeaSuring Instruments for Liquefied Petroleum Gas Plant Use 液化石油氣工廠用計測裝置 |
|
|
|
CNS 12481
2017 Edition Standard Blocks of Shore Hardness 蕭氏硬度標準塊 |
|
|
|
CNS 7997
2017 Edition Oil Tempered Chromium Vanadium Alloy Steel Wires for Valve Spring 閥彈簧用油回火鉻釩合金鋼鋼線 |
|
|
|
CNS 4569
2017 Edition T-Head BoltS with One-Rounded Head Ｔ形頭螺栓（具單邊圓角） |
|
|
|
CNS 5988
2017 Edition Stud Shanks for Press Dies 衝模用栓柄 |
|
|
|
CNS 6402
2017 Edition Set Screw for Jig Bushings 鑽模導套用固定螺釘 |
|
|
|
CNS 14811
2017 Edition Method of teSt for field measurement of soil resistivity using the Wenner four-electrode method 現場土壤電阻率之維納（Wenner）四極測定法 |
|
|
|
CNS 9240
2017 Edition Method of TeSt for Low Freguency(Below 3 MHz) Electrical Connectors(TP - 18 Visual and Dimensional Inspection) 頻率３ＭＨｚ以下電連接器檢驗法（外觀及尺度檢查ＴＰ–１８） |
|
|
|
CNS 15285
2017 Edition General requirementS and test methods for chargers used by mobile terminals and other hand-held ICT devices 用於行動終端及其他手持資通訊技術裝置之充電器一般規定及測試方法 |
|
|
|
CNS 13166
2017 Edition InSpection for Flash Welds (Steel) 閃電熔接部之檢驗法（鋼） |
|
|
|
CNS 14623-1
2017 Edition Sterilization of health care products-chemical indicators-Part 1：General requirements 保健產品之滅菌─化學指示劑─第一部分：一般規定 |
|
|
|
CNS 15992
2017 Edition Method of teSt for flow of hydraulic cement mortar 水硬性水泥砂漿流度試驗法 |
|
|
|
CNS 10698
2017 Edition Method of TeSt for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Squelch Blocking, Receiver Attack and Closing Time) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（靜音截斷、接收機動作及閉合時間） |
|
|
|
CNS 5804
2017 Edition Carbon Steel Pipes for High Temperature Service 高溫配管用碳鋼鋼管 |
Translated |
|
|
CNS 4227
2017 Edition Thread and Thread EndS for Wood Screws 木螺釘螺紋 |
|
|
|
CNS 4416
2017 Edition Slotted Flat Mushroom Head Screws 有槽平蕈形頭螺釘 |
|
|
|
CNS 2861
2017 Edition Steel balls for ball bearings 滾珠軸承用鋼珠 |
|
|
|
CNS 3371
2017 Edition Hand TapS for Metric Coarse Thread, Class 3 公制粗牙手力螺絲攻，精度３級 |
Translated |
|
|
CNS 8226
2017 Edition Method of TeSt for Dry Reed Switches (Visual and Mechanical Inspection) 乾式簧開關檢驗法（目視與機械檢驗） |
|
|
|
CNS 14445
2017 Edition Method of teSt for flexure(modulus of rupture,modulus of elasticity)of slate 板岩撓曲試驗法 |
|
|
|
CNS 3608
2017 Edition End MillS with Straight Shank 直柄端銑刀 |
Translated |
|
|
CNS 2323
2017 Edition Barbed Wire 棘鐵絲 |
|
|
|
CNS 15329-7
2017 Edition Information technology - Radio frequency identification device conformance teSt methods - Part 7: Test methods for active air interface communications at 433 MHz 資訊技術－無線射頻識別裝置符合性測試方法－第７部：４３３ＭＨｚ主動式空中介面通信之測試方法 |
|
|
|
CNS 14546
2017 Edition LED traffic Signal lanterns and lamp housing 發光二極體交通號誌燈燈面及燈箱 |
|
|
|
CNS 11073
2017 Edition Copper and copper alloy Sheets, plates and strips 銅及銅合金板及捲片 |
|
|
|
CNS 16015-2
2017 Edition TranSportation of dangerous goods − Part 2: Dangerous goods list 危險貨物之運輸－第2部：危險貨物表 |
|
|
|
CNS 12290
2017 Edition Reliability ASsured Fixed Metal Film Resistors (C,E) 可靠度保證金屬皮膜固定電阻器（特性Ｃ及Ｅ） |
Translated |
| Find out:16181Items | To Page of: First -Previous-Next -Last | [370] [371] [372] [373] [374] [375] [376] |
