"E " CNS Standards List| Implants surgery | Method Test | Standard Nominal | Acetone | Industrial automation | Basic | General Rules | Tools pressing | |
|
CNS 10898
2017 Edition Flat Quick-ConnEct Terminals 平板型接頭 |
|
|
|
CNS 2598
2017 Edition Charcoal for fuEl use 木炭(燃料用) |
|
|
|
CNS 4691
2017 Edition Studs for Stud WElding With Tip Ignition; Threaded Studs 尖端燃熔用螺樁 |
|
|
|
CNS 7961
2017 Edition MEthod of Test for Portable Chronometric Tachometers 攜帶型轉速計檢驗法 |
|
|
|
CNS 4697
2017 Edition CountErsunk Bolts With Double Nip 平頂埋頭雙鰭螺栓 |
|
|
|
CNS 5672
2017 Edition Arbor End Collars for Milling Machines 銑刀心軸端軸環 |
|
|
|
CNS 783-6
2017 Edition Sodium carbonatE for industrial use - Part 6 : Determination of matter insoluble in water at 50℃ 工業用碳酸鈉－第６部：50℃水不溶物測定法 |
|
|
|
CNS 15558-1
2017 Edition FlExible cellular polymeric materials - Physical properties - Part 1: General rules 軟質發泡材料－物理特性－第１部：通則 |
|
|
|
CNS 10957
2017 Edition TEst code for performance of circular sawing machines 圓鋸機動態檢驗法 |
|
|
|
CNS 15551-1
2017 Edition Ergonomics - Accessible design - Auditory signals for consumer products 人因工程－無障礙設計 - 消費產品之聲音訊號 |
|
|
|
CNS 10695
2017 Edition MEthod of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 14717
2017 Edition MEthod for calculation of physical properties of liquefied petroleum gases from compositional analysis 液化石油氣物理性質成分分析計算法 |
|
|
|
CNS 5892
2017 Edition Nylon FilamEnt Fabrics (Finished) 尼龍絲織物（漂染後） |
|
|
|
CNS 5820
2017 Edition Silica PowdEr (White Carbon) (for Rubber Use) 二氧化矽粉（橡膠用） |
Translated |
|
|
CNS 5774
2017 Edition ThErmistor Rods, Insulated (Style TRC) 管形絕緣熱敏電阻器（型號ＴＲＣ） |
|
|
|
CNS 312
2017 Edition Tap AdaptEr 絲公接桿 |
|
|
|
CNS 14179
2017 Edition REliability tests for digital transmitter and receiver modules used for optical fiber communication 光纖通信用數位傳輸和接收模組之可靠度測試 |
|
|
|
CNS 4562
2017 Edition Cross REcessed Round Head Wood Screws 十字穴圓頭木螺釘 |
Translated |
|
|
CNS 5500
2017 Edition Badial SElf-aligning Ball Bearings, Parallel and Tapered Bore 自動對位滾珠軸承（平行孔與推拔孔） |
|
|
|
CNS 9235
2017 Edition MEthod of Test for Dry Reed Switches(Application Notes) 乾式簧開關檢驗法（使用時注意事項） |
|
|
|
CNS 14102
2017 Edition Manual scanning B-modE ultrasonic diagnostic equipment 手動掃描Ｂ型超音波診斷裝置 |
|
|
|
CNS 12558
2017 Edition MEthod of Test for Solar Water Heater System (Automatic Cycle) 自然循環式太陽能熱水系統檢驗法 |
|
|
|
CNS 7004
2017 Edition ParallEl Shank Twist Drills for Use in Jig Bushes 鑽模導套用蔴花鑽（圓柱柄） |
|
|
|
CNS 15625-2
2017 Edition Paragliding Equipment – Paragliders – Part 2: Requirements and test methods for classifying flight safety characteristics 飛行傘設備─飛行傘─第2部：飛行安全性分類要求與試驗法 |
|
|
|
CNS 2648
2017 Edition MEthod of Test for Kraft-Paper Tape (Water Soluble, for Polywood Manufacture) 牛皮紙膠帶（水溶性，合板用）檢驗法 |
|
|
|
CNS 2602
2017 Edition PrEtensioned spun concrete piles 離心法先拉式預力混凝土基樁 |
|
|
|
CNS 4652
2017 Edition SlottEd Headless Screws with Chamfered End 有槽無頭去角端螺釘 |
|
|
|
CNS 4846
2017 Edition HExagon Head Pipe Plugs with Taper Thread 六角頭管塞（具推拔螺紋） |
|
|
|
CNS 4658
2017 Edition Tommy ScrEws with Fixed Clamping Bolt 貫頭螺釘（固定扳桿型） |
|
|
|
CNS 8651
2017 Edition TEst Code for Accuracy of Veneer Clippers 單板裁剪機精度檢驗標準 |
|
| Find out:15848Items | To Page of: First -Previous-Next -Last | [355] [356] [357] [358] [359] [360] [361] |
