"P V " CNS Standards List |
|
CNS 15130-2-1
2019 Edition Tests on electric and optical fibre cables under fire conditions − Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable – Apparatus 電纜及光纜之燃燒試驗－ 第2-1部：單條小型絕緣電線或電纜之垂直火焰延燃試驗－ 裝置 |
|
|
|
CNS 15040
2019 Edition Paints and varnishes - Determination of the volatile organic compound content of low - VOC emulsion paints (in-can VOC) 塗料與清漆－低ＶＯＣ乳膠漆（罐內ＶＯＣ）揮發性有機化合物含量之測定 |
|
|
|
CNS 15755-2-1
2019 Edition Conversion tables for units − Part 2-1: Length − Millimeter and inch 單位換算表－第2-1 部：長度－毫米與英寸 |
|
|
|
CNS 15117
2019 Edition Photovoltaic systems − Power conditioners − Procedure for measuring efficiency 太陽光電系統－電力調節器－量測效率之程序 |
|
|
|
CNS 4063
2019 Edition Reinforced Concrete Covers for Ditches (U Type) 鋼筋混凝土Ｕ形溝用蓋 |
Translated |
|
|
CNS 16101
2019 Edition Specification and qualification of welding procedures for metallic materials − Qualification based on previous welding experience 金屬材料銲接程序規範書及其檢定－依〝先前銲接經驗〞檢定 |
|
|
|
CNS 14432-2
2019 Edition Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions − Method by analysis of evolved carbon dioxide − Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test 塑膠材料在控制堆肥條件下最終好氧生物分解度測定法－二氧化碳釋出量分析法－第2部：實驗室規模重量測定法 |
|
|
|
CNS 7270
2019 Edition Method of Test for Vinylon Ropes 維尼龍繩索檢驗法 |
|
|
|
CNS 30
2019 Edition Belt drives − Pulleys − Quality, finish and balance 皮帶傳動－皮帶輪－品質、加工及平衡 |
|
|
|
CNS 9487
2019 Edition Bronze Screw down Check Globe Valves for Marine Use (5 kgf / ㎠) (Union Bonnet Type) 船用青銅管套帽型螺桿止回球形閥（5 kgf/㎠） |
|
|
|
CNS 15077-3
2019 Edition Test conditions for machining centres - Part 3 : Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis) 切削中心機之檢驗條件－第３部：具整合型分段指示或連續萬向分度頭之機器幾何檢驗（垂直Ｚ軸） |
|
|
|
CNS 16109
2019 Edition Test method for current-voltage (I-V) performance measurement of organic photovoltaic (OPV) and dye-sensitized solar cell (DSSC) 有機與染料敏化太陽能電池－ 電流-電壓性能量測試驗法 |
|
|
|
CNS 15685
2019 Edition Method of test for grain size of coated abrasive microgrits (P240-P2500) 砂紙、砂布用細粒磨料粒度試驗法 |
|
|
|
CNS 10314
2019 Edition 600 V Grade polyethylene insulated wires for electrical apparatus 電機器具用600 V 聚乙烯絕緣電線 |
|
|
|
CNS 15725
2019 Edition Belt drives − Pulleys for V-belts (system based on datum width) − Geometrical inspection of grooves 皮帶傳動－使用三角皮帶之皮帶輪(以基準寬度為基礎之系統)－溝槽之幾何檢驗 |
|
|
|
CNS 4767
2019 Edition Cotton Blended Spun Yarns and Viscose Rayon Blended Spun Yarns, Cotton System,Finished 棉混紡紗及黏液嫘縈棉混紡紗（棉紡式，漂染紗） |
|
|
|
CNS 3914
2019 Edition General Rules for Inspection of Marine Valves and Cocks 船用閥及旋塞之檢查通則 |
|
|
|
CNS 15062
2019 Edition Paints and varnishes - Testing of formaldehyde-emitting coatings and melamine foams - Determination of the steady-state concentration of formaldehyde in a small test chamber 塗料－逸散甲醛塗膜與三聚氰胺泡棉試驗法－小型容器中恒定狀態甲醛濃度之測定 |
|
|
|
CNS 15186-2
2019 Edition Cleanrooms and associated controlled environments – Part 2: Specifications for testing and monitoring to prove continued compliance with CNS 15186-1 潔淨室及其附屬之控制環境－第２部：確保持續符合ＣＮＳ １５１８６－１之測試與監測規範 |
|
|
|
CNS 16108-1
2019 Edition Railway applications − Fire protection on railway vehicles − Part 1: General 鐵路應用－鐵路車輛防火－第1部：通則 |
|
|
|
CNS 15755-5-7
2019 Edition Conversion tables for units − Part 5-7: Pressure or stress − Kilopascal and millimeter of water 單位換算表－第5-7 部：壓力或應力－千帕斯卡與毫米水柱 |
|
|
|
CNS 14004
2019 Edition Environmental management systems − General guidelines on implementation 環境管理系統－實施之一般指導綱要 |
|
|
|
CNS 16107-2
2019 Edition Hollow taper interface with flange contact surface − Part 2: Receivers − Dimensions 具凸緣接觸面之空心錐度界面－第2部：接收器尺度 |
|
|
|
CNS 2566
2019 Edition Polyester Staple Fiber Woven Fabrics (Unfinished) 聚酯棉狀纖維 |
Translated |
|
|
CNS 15176-26-1
2019 Edition Wind turbines − Part 26-1: Time-based availability for wind turbine generating systems 風力機－第26-1 部：風力發電機系統以時間為基礎之可利用率 |
|
|
|
CNS 15755-6-3
2019 Edition Conversion tables for units − Part 6-3: Work − Joule and kilogram-force meter 單位換算表－第6-3 部：功－焦耳與公斤力公尺 |
|
|
|
CNS 15196
2019 Edition Salt mist corrosion testing of photovoltaic (PV) modules 太陽光電模組之鹽霧腐蝕試驗 |
|
|
|
CNS 15876-7
2019 Edition Specification and qualification of welding procedures for metallic materials − Welding procedure test − Part 7: Overlay welding 金屬材料銲接程序規範書及其檢定－銲接程序試驗－第7部：堆銲 |
|
|
|
CNS 11391
2019 Edition Decorative electroplated coatings of copper/nickel/chromium on plastics 塑膠裝飾用之銅鎳鉻電鍍層 |
|
|
|
CNS 15660-2
2019 Edition Test conditions for numerically controlled turning machines and turning centres − Part 2: Geometric tests for machines with a vertical workholding spindle 數值控制車床及車削中心機之試驗條件－ 第2部：立式工件夾持主軸工具機之幾何試驗 |
|
| Find out:3530Items | To Page of: First -Previous-Next -Last | [30] [31] [32] [33] [34] [35] [36] |
