"n " CNS Standards List |
|
CNS 4301
2017 Edition Test Code for Accuracy of Surface Grinding Machines with Vertical Grinding Wheel Spindle and Rotary Table 旋轉床台型立式平面磨床精度檢驗標準 |
|
|
|
CNS 15077-10
2017 Edition Test conditions for machining centres - Part 10: Evaluation of thermal distortions 切削中心機之檢驗條件－ 第10部：熱變形之評估 |
|
|
|
CNS 4071
2017 Edition P-Methylaminophenol Sulfate (Metol) 氣動盤形輪磨機 |
Translated |
|
|
CNS 407
2017 Edition Symbols of Transformers 變壓器符號 |
|
|
|
CNS 4578
2017 Edition Bolted Connections with Reduced Booy; Metric Thread with Large Clearence, Nominal Values and Limits 減徑柄螺栓之結合法–具大間隙之公制螺紋（標稱尺寸與限界尺寸） |
|
|
|
CNS 12291
2017 Edition General Rules for Reliability Assured Fixed Carbon Composition Resistors 可靠度保證混合碳固定電阻器總則 |
|
|
|
CNS 517
2017 Edition Metric Buttress Screw Thread, Allowance and Tolerance 公制鋸齒形螺紋（裕度及公差） |
|
|
|
CNS 4363
2017 Edition Slotted Countersunk (Flat) Head Screws for Fine Mechanics M 0.4 to M 1.4 精密用有槽平頂埋頭螺釘（標稱直徑自0.4mm至1.4mm） |
|
|
|
CNS 12865-9
2017 Edition Method of Test for Digital Microelectronics ( Delay Measurements ) 數位微電子檢驗法（延遲量測） |
|
|
|
CNS 14613
2017 Edition 1800 MHz GSM mobile telephone system - Air interface １８００ＭＨｚＧＳＭ行動電話系統－空中介面 |
|
|
|
CNS 15499-2
2017 Edition Electrically propelled road vehicles – Safety specifications – Part 2: Vehicle operational safety means and protection against failures 電動推進道路車輛－安全規範－第2部:車輛操作安全方法及故障防護 |
|
|
|
CNS 6083
2017 Edition Lock nuts for Rigid Steel Conduits 電線用鋼管鎖帽 |
|
|
|
CNS 5666
2017 Edition Spindle Noses for Milling Machines 銑床主軸鼻端 |
|
|
|
CNS 14137
2017 Edition Method of eddy current test for titanium pipes and tubes 鈦管渦電流檢測法 |
|
|
|
CNS 7999
2017 Edition Oil Tempered Chromium Silicon Alloy Steel Wires for Valve Springs 閥彈簧用油回火矽鉻合金鋼鋼線 |
|
|
|
CNS 6150
2017 Edition Method of Test for Electromechanical Switches(Terminal Temperature Rise) 電機開關檢驗法–端子溫度上昇 |
|
|
|
CNS 14623-2
2017 Edition Sterilization of health care products-chemical indicators-Part 2：Test equipment and methods 保健產品之滅菌─化學指示劑─第二部分：測試設備與方法 |
|
|
|
CNS 14489
2017 Edition Manipulating industrial robots-Presentation of characteristics 工業用機器人-特性之標示 |
|
|
|
CNS 3714
2017 Edition Hand-Supported Hair Dryers 手提型頭髮吹風機 |
Translated |
|
|
CNS 14659
2017 Edition Acoustics - Determination of sound power levels of noise sources using sound pressure - Comparison method in situ 聲學─利用聲壓測定噪音源聲功率位準─現場的比較法 |
|
|
|
CNS 1142
2017 Edition Pliers and nippers - Lever assisted side cutting pliers 夾鉗與剪鉗試驗法 |
|
|
|
CNS 3326
2017 Edition Safety Code of High Pressure for Freeging Devices 冷凍設備高壓安全規章 |
|
|
|
CNS 10607
2017 Edition Hair Curling Appliances 鬈髮器 |
Translated |
|
|
CNS 660
2017 Edition Method of Test for Head Loss of Water Pumps 水泵工作位差檢驗法 |
|
|
|
CNS 15581
2017 Edition Grading rules for hardwood sawn lumber 闊葉樹製材分等 |
|
|
|
CNS 6081
2017 Edition Elbows for Rigid Steel Conduits 電線用鋼管彎頭 |
|
|
|
CNS 11570
2017 Edition Remote Control Relays and Remote Control Switches 遙控電驛及遙控開關 |
|
|
|
CNS 13288
2017 Edition Basic Environmental Testing Procedures Part 2: Tests - Guidance on Change of Temperature Tests 環境試驗法（電氣、電子）–溫度變化試驗之指引 |
|
|
|
CNS 12569
2017 Edition Method of test for fruit and vegetable juice products - Determination of soluble solids 水果及蔬菜汁飲料檢驗法－可溶性固形物之測定 |
|
|
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [337] [338] [339] [340] [341] [342] [343] |
