"C " CNS Standards List |
|
CNS 4970
2017 Edition Boxes for UnplastiCized Polyvinyl Chloride (UPVC) Conduit 硬質聚氯乙烯電氣接線盒 |
Translated |
|
|
CNS 15535
2017 Edition FluoresCent induction lamps - Safety requirements 感應式螢光燈－安全性要求 |
|
|
|
CNS 9944
2017 Edition Method of Test for Strain of OptiCal Glasses 光學玻璃應變試驗法 |
Translated |
|
|
CNS 9240
2017 Edition Method of Test for Low FreguenCy(Below 3 MHz) Electrical Connectors(TP - 18 Visual and Dimensional Inspection) 頻率３ＭＨｚ以下電連接器檢驗法（外觀及尺度檢查ＴＰ–１８） |
|
|
|
CNS 14369
2017 Edition MiCrographics-Reader-printers for transparent microforms-Characteristics 微縮技術－透明微縮品閱讀影印機－特性 |
|
|
|
CNS 2571
2017 Edition Safety Code for Storage Transporation and Use of Liquefied Chlorine 液氯儲運使用安全規章 |
|
|
|
CNS 12664
2017 Edition Method of Test for QualifiCation Procedure of Welding Technique of Plastics 鑑定熔接塑膠技術之試驗法 |
|
|
|
CNS 6135-3
2017 Edition Hearing aid-Part3: Hearing aids equipment not entirely worn on the listener 助聽器－第3部:不完全配戴在聽者身上的助聽設備 |
|
|
|
CNS 508
2017 Edition KnuCkle Thread (Profiles, Nominal Sizes) 圓螺紋（螺紋輪廓基本尺寸） |
|
|
|
CNS 6834-3
2017 Edition Testing methods for rubber and plastiCs hoses - Part 3: Determination of resistance to vacuum 橡膠管及塑膠管試驗法－第3部：耐負壓試驗 |
|
|
|
CNS 7377
2017 Edition Seamless Steel Tubes for High Pressure Gas Cylinder 高壓貯氣瓶用無縫鋼管 |
Translated |
|
|
CNS 502
2017 Edition ISO MetriC Fine Screw Threads (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5（ISO制）（標稱直徑12至80公釐，螺距1.5公釐） |
|
|
|
CNS 4560
2017 Edition Cross Recessed Countersunk (Flat) Head Screws 十字穴平頂埋頭螺釘 |
Translated |
|
|
CNS 6090
2017 Edition Circular Surface Boxes for Rigid Steel Conduits 電線用鋼管圓形匣 |
|
|
|
CNS 14492-6
2017 Edition Methods of measurement on radio reCeivers for various classes of emission -Part 6：General purpose communication receivers 不同發射類別之無線電接收機的量測方法─第６部：一般用途通訊接收機 |
|
|
|
CNS 4655
2017 Edition Hexagon Set SCrews with Half Dog Point and Cone End 六角頭短柱錐形端固定螺釘 |
|
|
|
CNS 247
2017 Edition MaChine Reamer, with Square Head 機用鉸刀（方頭圓柱柄） |
|
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 13144
2017 Edition Method of Test for Internal Bonding Strength of Paper and Paperboard ( Using Tensile Strength Tester ) 紙及紙板內部結合強度試驗法（使用抗張強度試驗機) |
Translated |
|
|
CNS 14623-2
2017 Edition Sterilization of health Care products-chemical indicators-Part 2：Test equipment and methods 保健產品之滅菌─化學指示劑─第二部分：測試設備與方法 |
|
|
|
CNS 12867
2017 Edition BasiC Environmental Testing Procedures Part 2 : Tests-Test Z/AM : Combined Dry Heat/Low Air Pressure Tests 環境試驗法（電氣、電子）–高溫／低氣壓複合試驗法 |
|
|
|
CNS 1021
2017 Edition PiCks, One Flat End and One Taper End 十字鎬（一端為尖錐狀，一端為鋼撬狀） |
|
|
|
CNS 4573
2017 Edition Slotted Raised Countersunk Bolts for Drawing Instruments 有槽扁圓頂埋頭螺栓（繪圖儀器用） |
|
|
|
CNS 10113
2017 Edition Method for Determining Fluorine Content in Natural and Artificial Cryolite (Modified Willard Winter Method) 天然及人造冰晶石中氟定量法（改良威拉–溫特法） |
|
|
|
CNS 11570
2017 Edition Remote Control Relays and Remote Control Switches 遙控電驛及遙控開關 |
|
|
|
CNS 4122
2017 Edition Type A1 standard test bloCk for ultrasonic testing 超音波檢測用Ａ１型標準規塊 |
|
|
|
CNS 6080
2017 Edition Couplings for Rigid Steel Conduits 電線用鋼管管接頭 |
Translated |
|
|
CNS 5284
2017 Edition Addendum ModifiCation of Spur Gears in the 0.5 System, Introduction ０．５齒制正齒輪之齒廓移位 |
|
|
|
CNS 9104
2017 Edition Symbols of Meters of Interior Wiring Diagram for ArChitectural Plans 屋內配線設計圖計器類符號 |
|
|
|
CNS 225
2017 Edition Shell Drills (Shell Counterborer) of High Speed Steel 殼形擴孔鑽 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [335] [336] [337] [338] [339] [340] [341] |
