"H " CNS Standards List |
|
CNS 6082
1993 Edition BusHings for Rigid Steel Conduits 電線用鋼管管口護套 |
Translated |
|
|
CNS 6772
1993 Edition MetHods of Test for Insulating Porcelains 絕緣瓷器試驗法 |
|
|
|
CNS 12887
1993 Edition MetHod of Test for Accelerated Aging of Paper and Paperboard - Moist Heat Treatment at 90℃ and 25% R.H. 紙及紙板加速老化試驗法－90 ℃及25 %R．H．濕熱處理 |
Translated |
|
|
CNS 4434
1993 Edition Round Nuts WitH Drilled Holes in One Face 頂孔圓螺帽 |
|
|
|
CNS 101
1993 Edition Accuracy Inspection of Floor Type Horizontal Boring Machines 落地型臥式搪床精度檢驗 |
Translated |
|
|
CNS 4688
1993 Edition Studs for Drawn Arc Stud Welding - UntHreaded Studs 電弧樁熔接用柱樁－無螺紋樁 |
|
|
|
CNS 100
1993 Edition Accuracy Inspection of Table Type Horizontal Boring Machines 床台型臥式搪床精度檢驗 |
Translated |
|
|
CNS 99
1993 Edition Accuracy Inspection of Slotting MacHines 插床精度檢驗 |
Translated |
|
|
CNS 13163
1993 Edition MetHod of Soundness Test for Fillet Welds 填角熔接部之無瑕疵試驗法 |
|
|
|
CNS 98
1993 Edition Accuracy Inspection of SHaping Machines 牛頭刨床精度檢驗 |
Translated |
|
|
CNS 97
1993 Edition Test Code for Performance and Accuracy of Double Housing Type Planing Machines 門型龍門刨床精度檢驗與動態檢驗法 |
Translated |
|
|
CNS 13217
1993 Edition Cold Rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 冷軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 96
1993 Edition Test Code for Performance and Accuracy of Radial Drilling MacHines 旋臂鑽床精度檢驗與動態檢驗法 |
Translated |
|
|
CNS 4881
1993 Edition Tires for Industrial VeHicles and Off the Road Service 工業車輛及工程機械用輪胎 |
Translated |
|
|
CNS 12886
1993 Edition MetHod of Test for Accelerated Aging of Paper and Paperboard - Dry Heat Treatment at 105℃ 紙及紙板加速老化試驗法－105 ℃乾熱處理 |
Translated |
|
|
CNS 13213
1993 Edition Procedures for Temperature and Irradiance Corrections to Measured I-V CHaracteristics of Crystalline Silicon Photovoltaic Devices 對矽晶光電元件之電流電壓特性測量值做溫度與輻射校正之程序 |
|
|
|
CNS 10378
1993 Edition MetHod of Test for Folding Endurance of Paper and Paperboard (MIT Tester) 紙及紙板耐折強度試驗法（MIT試驗機） |
Translated |
|
|
CNS 95
1993 Edition Accuracy Inspection of UprigHt Drilling Machines 直立鑽床精度檢驗 |
Translated |
|
|
CNS 4433
1993 Edition Round Nuts WitH Set Pin Hole in Side 側孔圓螺帽 |
|
|
|
CNS 737
1993 Edition MetHod of Test for Rubber Pneumatic Tires for Bicycles 自行車用橡膠外胎檢驗法 |
Translated |
|
|
CNS 4687
1993 Edition Studs for Drawn Arc Stud Welding - THreaded Studs 電弧樁熔接用柱樁－螺紋樁 |
|
|
|
CNS 13216
1993 Edition Hot - rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 熱軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 13198
1993 Edition Fixed Multilayer Ceramic CHip Capacitors for Use in Electronic Equipment 電子設備用固定多層陶瓷晶片電容器 |
|
|
|
CNS 853
1993 Edition Cross Joints WitH Quadri - Flange (Working Pressure Less Than 16 kgf/c㎡) 凸緣十字管接頭(使用壓力16 kgf/cm2) |
|
|
|
CNS 13166
1993 Edition Inspection for FlasH Welds (Steel) 閃電熔接部之檢驗法（鋼） |
|
|
|
CNS 13165
1993 Edition MetHod of Macro Test for Section of Spot Welded Joints 點熔接接合之斷面巨觀試驗法 |
|
|
|
CNS 13252
1993 Edition MetHod of Tension Test for Spot Welded Joints 點熔接接合之拉伸試驗法 |
|
|
|
CNS 12566
1993 Edition Basic Environmental Testing Procedures Part 2: Tests, Test Z/AD:Composite Temperature/Humidity Cyclic Test 環境試驗法（電氣、電子）－溫濕度組合（循環）試驗 |
|
|
|
CNS 5974
1993 Edition Cast Iron Flanged Swing CHeck Valves (10kgf/c㎡) 鑄鐵凸緣型擺動式止回閥(10 kgf/cm2) |
Translated |
|
|
CNS 13253
1993 Edition MetHod of Inspection for Spot Welds 點熔接部之檢驗法 |
|
| Find out:11384Items | To Page of: First -Previous-Next -Last | [330] [331] [332] [333] [334] [335] [336] |
