"H " CNS Standards List| Base Tangent | Method Test | Involute Splines | Method Test | Single phase | Gaseous hydrogen | General Rules | Uninterruptible power | |
|
CNS 13194
1993 Edition Test MetHods for Performance and Accuracy of Double Sizers 雙端截鋸機之性能試驗及精度檢驗法 |
|
|
|
CNS 97
1993 Edition Test Code for Performance and Accuracy of Double Housing Type Planing Machines 門型龍門刨床精度檢驗與動態檢驗法 |
Translated |
|
|
CNS 4433
1993 Edition Round Nuts WitH Set Pin Hole in Side 側孔圓螺帽 |
|
|
|
CNS 4434
1993 Edition Round Nuts WitH Drilled Holes in One Face 頂孔圓螺帽 |
|
|
|
CNS 3633
1993 Edition Basic Environmental Testing Procedures Part 2: Tests, Test N: CHange of Temperature 環境試驗法（電氣、電子）－溫度變化試驗 |
|
|
|
CNS 12886
1993 Edition MetHod of Test for Accelerated Aging of Paper and Paperboard - Dry Heat Treatment at 105℃ 紙及紙板加速老化試驗法－105 ℃乾熱處理 |
Translated |
|
|
CNS 13165
1993 Edition MetHod of Macro Test for Section of Spot Welded Joints 點熔接接合之斷面巨觀試驗法 |
|
|
|
CNS 94
1993 Edition Accuracy Inspection of LatHes 車床精度檢驗 |
Translated |
|
|
CNS 4881
1993 Edition Tires for Industrial VeHicles and Off the Road Service 工業車輛及工程機械用輪胎 |
Translated |
|
|
CNS 13198
1993 Edition Fixed Multilayer Ceramic CHip Capacitors for Use in Electronic Equipment 電子設備用固定多層陶瓷晶片電容器 |
|
|
|
CNS 13213
1993 Edition Procedures for Temperature and Irradiance Corrections to Measured I-V CHaracteristics of Crystalline Silicon Photovoltaic Devices 對矽晶光電元件之電流電壓特性測量值做溫度與輻射校正之程序 |
|
|
|
CNS 12887
1993 Edition MetHod of Test for Accelerated Aging of Paper and Paperboard - Moist Heat Treatment at 90℃ and 25% R.H. 紙及紙板加速老化試驗法－90 ℃及25 %R．H．濕熱處理 |
Translated |
|
|
CNS 9978
1993 Edition Quartz WatcH for Submersion 潛水石英錶 |
|
|
|
CNS 3874
1993 Edition MetHod of Test for the Tire Valves of Bicycles 自行車（腳踏車）車胎空氣閥檢驗法 |
Translated |
|
|
CNS 853
1993 Edition Cross Joints WitH Quadri - Flange (Working Pressure Less Than 16 kgf/c㎡) 凸緣十字管接頭(使用壓力16 kgf/cm2) |
|
|
|
CNS 13163
1993 Edition MetHod of Soundness Test for Fillet Welds 填角熔接部之無瑕疵試驗法 |
|
|
|
CNS 739
1993 Edition MetHod of Test for Rubber Inner Tubes for Bicycles 自行車用橡膠內胎檢驗法 |
|
|
|
CNS 13142
1993 Edition MetHod of Test for Ink Absorption of Paper ( K & N Ink Absorption Test ) 紙張吸墨度試驗法（K&N油墨吸收試驗法） |
Translated |
|
|
CNS 4624
1993 Edition Hot-Rolled Carbon Steel Strip for Pipes and Tubes 鋼管用熱軋碳鋼鋼帶 |
Translated |
|
|
CNS 13135
1993 Edition Test MetHods for Performance and Accuracy of Band Saws and Feed Equipment 帶鋸機及送材裝置之試驗及檢驗法 |
|
|
|
CNS 13164
1993 Edition MetHod of Tension Shear Test for Spot Welded Joints 點熔接接合之拉剪試驗法 |
|
|
|
CNS 13144
1993 Edition MetHod of Test for Internal Bonding Strength of Paper and Paperboard ( Using Tensile Strength Tester ) 紙及紙板內部結合強度試驗法（使用抗張強度試驗機) |
Translated |
|
|
CNS 101
1993 Edition Accuracy Inspection of Floor Type Horizontal Boring Machines 落地型臥式搪床精度檢驗 |
Translated |
|
|
CNS 6772
1993 Edition MetHods of Test for Insulating Porcelains 絕緣瓷器試驗法 |
|
|
|
CNS 13191
1993 Edition Test MetHods for Performance and Accuracy of Band Saws 木工帶鋸機之性能試驗及精度檢驗法 |
|
|
|
CNS 100
1993 Edition Accuracy Inspection of Table Type Horizontal Boring Machines 床台型臥式搪床精度檢驗 |
Translated |
|
|
CNS 1488
1993 Edition Knife SwitcHes (With Cover) 有蓋閘刀開關 |
Translated |
|
|
CNS 13193
1993 Edition Test MetHods for Performance and Accuracy of Rotary Clippers 迴轉式單板截剪機之性能試驗及精度檢驗法 |
|
|
|
CNS 13216
1993 Edition Hot - rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 熱軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 737
1993 Edition MetHod of Test for Rubber Pneumatic Tires for Bicycles 自行車用橡膠外胎檢驗法 |
Translated |
| Find out:11384Items | To Page of: First -Previous-Next -Last | [330] [331] [332] [333] [334] [335] [336] |
