"I " CNS Standards List |
|
CNS 4899
2017 Edition Test methods of fIxed resistors for use in electronic equipment 電子設備用固定電阻器檢驗法 |
|
|
|
CNS 10116
2017 Edition Method for DetermIning Aluminium Content in Natural and Artificial Cryolte {Oxine (8-Hydroxyquinoline) Gravimetric Method} 天然及人造冰晶石中鋁定量法〔喔星 ( 8 - 羥基喹啉 ) 重量法〕 |
|
|
|
CNS 16016-3
2017 Edition PlastIcs piping systems for hot and cold water installations − Polypropylene (PP) − Part 2: Pipes 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第3部：管件 |
|
|
|
CNS 15623
2017 Edition ParaglIding equipment – Emergency parachutes – Safety requirements and test methods 飛行傘設備－緊急降落傘－安全要求與試驗法 |
|
|
|
CNS 13653
2017 Edition Lot-Control TestIng for Light Emitting Diode(for Communication) 通信用發光二極體之批品質控制測試 |
|
|
|
CNS 12844
2017 Edition Method of Test for Chlorosulfonated Polyethylene Rubber Supported Geomembrane for LandfIll 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布檢驗法 |
Translated |
|
|
CNS 1197
2017 Edition Round FIle for Smith 鐵工用圓銼 |
Translated |
|
|
CNS 13867
2017 Edition Copper and copper alloy welded pIpes and tubes 銅及銅合金銲接管 |
|
|
|
CNS 14782
2017 Edition ManIpulating industrial robots —Test equipment and metrology methods of operation for robot performance evaluation 工業用機器人性能評估作業之測試儀器與量測方法 |
|
|
|
CNS 5772
2017 Edition ThermIstor Disks, Insulated (Style TDC) 盤形絕緣熱敏電阻器（型號ＴＤＣ） |
|
|
|
CNS 7930
2017 Edition Method of Test for FabrIc Sheets of Temporary Works for Buildings 建築工程用遮布檢驗法 |
|
|
|
CNS 7377
2017 Edition Seamless Steel Tubes for HIgh Pressure Gas Cylinder 高壓貯氣瓶用無縫鋼管 |
Translated |
|
|
CNS 11139
2017 Edition Formulated soymIlk 調製豆奶 |
|
|
|
CNS 3610
2017 Edition Two-Flute End MIlls with Straight Shank 兩刃直柄端銑刀 |
Translated |
|
|
CNS 13284
2017 Edition GuIde for Explosions Venting 洩爆指導要點 |
|
|
|
CNS 127
2017 Edition MetrIc Taper Gauge, with Flat Head 公制圓錐量規（有扁頭） |
|
|
|
CNS 9022
2017 Edition Methos of test for colour fastness to hIgh temperature steaming 耐高溫蒸熱染色堅牢度試驗法 |
|
|
|
CNS 4216
2017 Edition WIre Twister Pliers (with Side Cutter) 扭絲鉗（附邊剪器） |
Translated |
|
|
CNS 4552
2017 Edition Rounded TrapezoIdal Thread; Nominal Sizes 圓角梯形螺紋（標稱尺寸） |
|
|
|
CNS 3132
2017 Edition Hexagon Nuts wIth Small Widths Across Flats 小六角螺帽（機動車工業用） |
Translated |
|
|
CNS 13343
2017 Edition OIl Tempered Chromium Silicon Alloy Steel Wires for Springs 彈簧用油回火矽鉻合金鋼鋼線 |
|
|
|
CNS 4322
2017 Edition Hexagon Bolts wIth Thread Approximately to Head, Regular, Metric Thread 六角頭全螺紋螺栓（粗製） |
|
|
|
CNS 6351-3
2017 Edition OIl of spearmint - Part 3: Indian type (Mentha spicata L.), redistilled oil 綠薄荷油－第3部：印度型(再蒸餾油) |
|
|
|
CNS 14889
2017 Edition RIsk management - Vocabulary 風險管理－詞彙 |
|
|
|
CNS 3440
2017 Edition Method of test for mIlk and milk products - General rules 乳品檢驗法－總則 |
Translated |
|
|
CNS 505
2017 Edition ISO Metric Fine Screw Threads (Diameters from 42 to 300 mm and Pitch 4 mm) 公制細螺紋8（ISO制）（標稱直徑42至300公釐，螺距4公釐） |
|
|
|
CNS 5283
2017 Edition Accuracy of CylIndrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度（齒廓面元線誤差之公差） |
|
|
|
CNS 4309
2017 Edition ConIcal Spring Washers 圓錐彈簧墊圈 |
|
|
|
CNS 12735
2017 Edition Method of Test for L, a, b, 45°, 0° ColorImetry of White and Near-white Paper and Paper Board 白或近似白紙及紙板之Ｌ、ａ、ｂ值４５°、０°色度試驗法 |
Translated |
|
|
CNS 12292
2017 Edition RelIability Assured Fixed Carbon Composition Resistors (Established Failure Rate) 可靠度保證混合碳固定電阻器（故障率設定） |
Translated |
| Find out:15020Items | To Page of: First -Previous-Next -Last | [323] [324] [325] [326] [327] [328] [329] |
