"S " CNS Standards List |
|
CNS 5963
2017 Edition Bronze Screwed Globe Valves (10kgf/c㎡) 青銅螺紋口球形閥（10 kgf/㎠） |
|
|
|
CNS 2831
2017 Edition FixtureS for Aluminium Conducting Wires and Cables 鋁導體電線電纜用配件 |
|
|
|
CNS 5804
2017 Edition Carbon Steel Pipes for High Temperature Service 高溫配管用碳鋼鋼管 |
Translated |
|
|
CNS 6571
2017 Edition ESsential oils - Determination of relative density at 20 ℃ - Reference method 精油－相對密度（２０℃）測定法 |
|
|
|
CNS 2906
2017 Edition Carbon Steel Castings 碳鋼鑄鋼件 |
Translated |
|
|
CNS 6408
2017 Edition Calculation of Load Capacity for Cylindrical and Bevel GearS-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算–齒廓面作用帶因數Zн |
|
|
|
CNS 4790-5
2017 Edition GloSsary of terms used in pulp and paper industry ─ Terms of pulp, paper or board properties 紙漿與紙詞彙─紙漿、紙或紙板之性質及試驗名詞 |
|
|
|
CNS 11151
2017 Edition Method of TeSt for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 10522
2017 Edition Emergency Public AddreSs Equipment 消防用緊急廣播設備 |
Translated |
|
|
CNS 7248
2017 Edition Liquefied Petroleum GaStank on Truck or Trailer 液化石油氣汽車運輸槽體 |
|
|
|
CNS 503
2017 Edition ISO Metric Fine Screw Threads (Diameters from 18 to 150mm and Pitch 2mm) 公制細螺紋6（ISO制）（標稱直徑18至150公釐，螺距2公釐） |
|
|
|
CNS 13154
2017 Edition Cold rolled Special steel strips 冷軋特殊鋼鋼帶 |
|
|
|
CNS 4316
2017 Edition Mechanical PropertieS of Nuts-Effective Height of Thread < 0.4 d) 螺帽之機械性質（有效螺紋長度未滿０．４ｄ者） |
|
|
|
CNS 7549
2017 Edition PreciSion Square Levels 精密平板 |
|
|
|
CNS 1411
2017 Edition Container for Lead Acid BatterieS 鉛蓄電池用外殼 |
|
|
|
CNS 5487
2017 Edition PlierS and nippers - Slip joint pliers 夾鉗與剪鉗－萬能鉗 |
|
|
|
CNS 8876
2017 Edition Fire manual Station and its fire alarm bell indication lamp 火警發信機及其火警警鈴、標示燈 |
Translated |
|
|
CNS 11156
2017 Edition GreaSe Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 12729
2017 Edition Packaged Soybean curd (Tofu) 包裝豆腐 |
|
|
|
CNS 14257
2017 Edition Method of teSt for leakage rate respirator facepiece 呼吸防護具面體洩漏率試驗法 |
|
|
|
CNS 12865-7
2017 Edition Method of TeSt for Digital Microelectronics ( Drive Source, Dynamic ) 數位微電子檢驗法（驅動源，動態） |
|
|
|
CNS 9234
2017 Edition Method of TeSt for Dry Reed Switches (Standard Test Coils, Single Insulation 130 ℃ Wire) 乾式簧開關檢驗法（１３０℃單層絕緣線標準試驗線圈） |
|
|
|
CNS 5970
2017 Edition Bronze Flanged Angle ValveS (10kgf/c㎡) 青銅凸緣型角閥（10 kgf/㎠） |
|
|
|
CNS 3994
2017 Edition High Voltage Combination Starters 高壓綜合型起動盤 |
|
|
|
CNS 2115
2017 Edition Method of VickerS Hardness Test 維克氏硬度試驗法 |
|
|
|
CNS 15550
2017 Edition GuidelineS for standards developers to address the needs of older persons and persons with disabilities 標準發展者考量年長者與 身心障礙者需求之指導綱要 |
|
|
|
CNS 13418
2017 Edition Method of TeSt for Brightness for Mineral Fillers and Pigments for Paper Making (45° / 0° Directional Tester) 造紙用礦物質填料及顏料白度試驗法（４５° ／０°定向白度計法） |
Translated |
|
|
CNS 15988
2017 Edition Breath alcohol teSt devices for general use − Requirements and test methods 一般用呼氣酒精測試裝置－要求與試驗法 |
|
|
|
CNS 4688
2017 Edition Studs for Drawn Arc Stud Welding - Unthreaded Studs 電弧樁熔接用柱樁–無螺紋樁 |
|
|
|
CNS 12882
2017 Edition Method of TeSt for Hook Drawing Resistance of Cement Sack Paper Laminated with Plastic Woven Sheet 塑膠編織貼合水泥袋紙鈎裂強度試驗法 |
Translated |
| Find out:16181Items | To Page of: First -Previous-Next -Last | [322] [323] [324] [325] [326] [327] [328] |
