"L " CNS Standards List |
|
CNS 6006
2017 Edition Dimensions of Hitch for Power TiLlers 耕耘機用接頭 |
|
|
|
CNS 3509
2017 Edition Covered ELectrodes for Hardfacing 硬面銲被覆銲條 |
Translated |
|
|
CNS 12850
2017 Edition NoduLar Graphite Iron Flanged Lift Check Valves (10 kgf/㎠) 球狀石墨鑄鐵凸緣升降型止回閥（10 kgf/㎠） |
Translated |
|
|
CNS 2207
2017 Edition Limestone 石灰石 |
|
|
|
CNS 10865
2017 Edition Method of test for aLpha-, beta- and gamma- cellulose in pulp 紙漿中α-、β-、γ- 纖維素試驗法 |
|
|
|
CNS 12292
2017 Edition ReLiability Assured Fixed Carbon Composition Resistors (Established Failure Rate) 可靠度保證混合碳固定電阻器（故障率設定） |
Translated |
|
|
CNS 12087
2017 Edition Method of Test for Fiber Optic Devices (FOPT-82 FLuid Penetration Test for Filled Fiber Optic Cable) 光纖裝置檢驗法（充膠光纜流體滲透試驗ＦＯＴＰ–８２） |
|
|
|
CNS 14357-3
2017 Edition Information technoLogy - Generic coding of moving pictures and associated audio information - Part 3:Audio 資訊技術－動態影音資訊之同屬編碼－第３部：音訊 |
|
|
|
CNS 12731
2017 Edition Method of Test for the FLuorescent Component of Brightness of Pulp, Paper and Paperboard Quantitatively 紙漿、紙及紙板之白度中螢光成分定量試驗法 |
Translated |
|
|
CNS 5279
2017 Edition Dimensions of CyLindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 4661
2017 Edition Tommy Nuts with MovabLe Clamping Bolt 貫頭螺帽（滑動扳桿型） |
|
|
|
CNS 13217
2017 Edition CoLd Rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 冷軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 12085
2017 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode ScrambLer Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求ＦＯＴＰ–５４） |
|
|
|
CNS 13347
2017 Edition Method of Test for AcryLonitrile - Butadiene - Styrene (ABS) Plastic Fittings for Water Works 自來水用丙烯腈–丁二烯–苯乙烯（ABS）塑膠管接頭配件檢驗法 |
|
|
|
CNS 1623
2017 Edition CaLcium chloride (for drying) 乾燥用氯化鈣 |
|
|
|
CNS 3419
2017 Edition Safety Code for Power Press ( Power Press AuxiLiary Equipment ) 動力壓機安全規章（動力壓機輔助設備） |
|
|
|
CNS 1204
2017 Edition Heavy FLat File for Smith 鐵工用重式扁平銼 |
Translated |
|
|
CNS 14254
2017 Edition GLossary of terms for resperatory protective devices 呼吸防護具詞彙 |
|
|
|
CNS 5415
2017 Edition Bed SLides of Sewing Machines for Industrial Use 工業用縫紉機滑板 |
|
|
|
CNS 13378
2017 Edition Boron SteeL Wires for Cold Heading and Cold Forging 冷打及冷鍛用硼鋼鋼線 |
|
|
|
CNS 2863
2017 Edition Method of Test for ToLerances of Rolling Bearings 滾動軸承精度檢驗法 |
|
|
|
CNS 4665
2017 Edition Insert Nuts Heavy Type for PLastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 5509
2017 Edition RoLling Bearings; Bearings with Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 10237
2017 Edition HandLes for Cranes 起重機用手柄 |
|
|
|
CNS 13982-8
2017 Edition Methods of test for buLk down and feather − Part 8: Determination of fill power with steam conditioning 羽絨羽毛試驗法－第8部：蒸汽處理後蓬鬆度測定法 |
|
|
|
CNS 4744
2017 Edition C11 Type Connectors for Radio Frequency CoaxiaL Cables 射頻同軸Ｃ１１型連接器 |
|
|
|
CNS 8532
2017 Edition Method of test for coLour fastness to hot pressing 耐熱壓燙染色堅牢度試驗法 |
|
|
|
CNS 14492-6
2017 Edition Methods of measurement on radio receivers for various cLasses of emission -Part 6：General purpose communication receivers 不同發射類別之無線電接收機的量測方法─第６部：一般用途通訊接收機 |
|
|
|
CNS 11223
2017 Edition Methods for ChemicaL Analysis of Refractory Clay 耐火黏土化學分析法 |
|
|
|
CNS 14139
2017 Edition Measurement methods for the performance of transmitter and receiver moduLes used for wireless infrared communication 無線通信用紅外線傳輸和接收模組功能特性量測法 |
|
| Find out:14127Items | To Page of: First -Previous-Next -Last | [322] [323] [324] [325] [326] [327] [328] |
