"A " CNS Standards List |
|
CNS 3326
2017 Edition SAfety Code of High Pressure for Freeging Devices 冷凍設備高壓安全規章 |
|
|
|
CNS 10216
2017 Edition GlossAry of terms used in pressure vessels 壓力容器之用詞 |
|
|
|
CNS 15832-1-1
2017 Edition Method of test for coAting components − Part 1-1: General rule − Common test conditions 塗料成分試驗法－第1-1部：通則－一般試驗條件 |
|
|
|
CNS 4358
2017 Edition Slotted PAn Head Screws with Shoulder 有槽盤頭有肩螺釘 |
Translated |
|
|
CNS 7147
2017 Edition Steel CAstings for High Temperature and High Pressure Service 高溫高壓用鑄鋼件 |
|
|
|
CNS 15623
2017 Edition PAragliding equipment – Emergency parachutes – Safety requirements and test methods 飛行傘設備－緊急降落傘－安全要求與試驗法 |
|
|
|
CNS 14467-2
2017 Edition Audio-visual, video and television equipment and systems - Part5: Control, synchronization and address codes - Chapter2: Control system for two still projectors. Operation practice 視聽．影像及電視設備與系統-第５部：同步.控制及定址碼-第２章：兩靜止式投影機之控制系統－操作實務 |
|
|
|
CNS 10940
2017 Edition Precision SurfAce Plates 著色塗覆鍍鋅低碳鋼線 |
|
|
|
CNS 4560
2017 Edition Cross Recessed Countersunk (FlAt) Head Screws 十字穴平頂埋頭螺釘 |
Translated |
|
|
CNS 7930
2017 Edition Method of Test for FAbric Sheets of Temporary Works for Buildings 建築工程用遮布檢驗法 |
|
|
|
CNS 2862
2017 Edition Deep Groove BAll Bearings: Single - Row Without Filling Notch 徑向深溝滾珠軸承（單列、無填裝槽） |
Translated |
|
|
CNS 14489
2017 Edition MAnipulating industrial robots-Presentation of characteristics 工業用機器人-特性之標示 |
|
|
|
CNS 9669
2017 Edition Slotted OvAl Pan Head Machine Screws 有槽扁圓頂盤頭小螺釘 |
|
|
|
CNS 11570
2017 Edition Remote Control RelAys and Remote Control Switches 遙控電驛及遙控開關 |
|
|
|
CNS 524
2017 Edition Plug GAuge for Whitworth Thread (Go End Limit for Fine, Medium and Coarse Fits) 韋氏螺紋量柱（不通過端限界尺寸，精配，中配及粗配） |
|
|
|
CNS 15551-2
2017 Edition Ergonomics - Accessible design - Sound pressure levels of auditory signals for consumer products 人因工程－無障礙設計 - 消費 產品中聲音訊號之聲壓位準 |
|
|
|
CNS 3714
2017 Edition HAnd-Supported Hair Dryers 手提型頭髮吹風機 |
Translated |
|
|
CNS 12994
2017 Edition Method of DeterminAtion for total Carbon Content of Hardmetals (Gravimetric Method) 超硬合金全碳量測定法（重量法） |
|
|
|
CNS 5026
2017 Edition Welding TrAnsformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 3633
2017 Edition BAsic Environmental Testing Procedures Part 2: Tests, Test N: Change of Temperature 環境試驗法（電氣、電子）–溫度變化試驗 |
|
|
|
CNS 9243
2017 Edition Method of Test for Low Frequency(Below 3 MHz) ElectricAl Connectors(TP - 43 Cable Clamping (Bending Moment)) 頻率３ＭＨｚ以下電連接器檢驗法（彎曲試驗ＴＰ–４３） |
|
|
|
CNS 11774
2017 Edition Steel Pipes Lining with Rigid Polyvinyl Chloride Pipe for WAter Works 自來水用內襯聚氯乙烯塑膠硬質管之鋼管 |
|
|
|
CNS 15421
2017 Edition Office furniture - ChAirs 辦公室用椅 |
|
|
|
CNS 5804
2017 Edition CArbon Steel Pipes for High Temperature Service 高溫配管用碳鋼鋼管 |
Translated |
|
|
CNS 13068
2017 Edition Methods of test for totAl amine values of amine-based hardeners of epoxy resins 環氧樹脂之胺系硬化劑總胺價試驗法 |
Translated |
|
|
CNS 15995
2017 Edition Rubber hoses And hose assemblies for liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas up to 25 bar (2.5 MPa) 2.5 MPa以下液相或氣相液化石油氣 (LPG)及天然氣用橡膠管及橡膠管組合件 |
|
|
|
CNS 5772
2017 Edition Thermistor Disks, InsulAted (Style TDC) 盤形絕緣熱敏電阻器（型號ＴＤＣ） |
|
|
|
CNS 12865-9
2017 Edition Method of Test for DigitAl Microelectronics ( Delay Measurements ) 數位微電子檢驗法（延遲量測） |
|
|
|
CNS 502
2017 Edition ISO Metric Fine Screw ThreAds (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5（ISO制）（標稱直徑12至80公釐，螺距1.5公釐） |
|
|
|
CNS 14492-1
2017 Edition Methods of meAsurement on radio receivers for various classes of emission-Part1:General considerations and methods of measurement,including audio-frequency measurements 不同發射類別之無線電接收機的量測方法-第1部:概論及含括音頻量測在內的量測方法 |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [320] [321] [322] [323] [324] [325] [326] |
