"L, " CNS Standards List |
|
CNS 13037
2017 Edition Covered electrodes for atmospheric corrosion resisting steel 耐候性鋼用被覆銲條 |
|
|
|
CNS 10865
2017 Edition Method of test for alpha-, beta- and gamma- cellulose in pulp 紙漿中α-、β-、γ- 纖維素試驗法 |
|
|
|
CNS 783-2
2017 Edition Sodium carbonate for industriaL use - Part 2 : Determination of loss of mass and of non-volatile matter at 250 ℃ 工業用碳酸鈉－第２部：250℃加熱減量及不揮發物測定法 |
|
|
|
CNS 4357
2017 Edition Slotted Pan Head Screws 有槽盤頭螺釘 |
Translated |
|
|
CNS 12406
2017 Edition Compressor for Liquefied Petroleum Gas Use 液化石油氣用壓縮機 |
|
|
|
CNS 173
2017 Edition Key Section and Tolerance (Cold Drawing) 鍵鋼剖面及偏差（冷拉） |
|
|
|
CNS 6763
2017 Edition ParalleL Shank Counterborer with Solid Pilot 具固定導桿之柱坑鑽（圓柱柄） |
|
|
|
CNS 4797-5
2017 Edition Toy Safety (ChemicaL Toys (Sets) Other Than Experimental Sets) 玩具安全（非實驗套組之化學玩具套組） |
Translated |
|
|
CNS 12592
2017 Edition Method of Test for TotaL Wax Content of Corrugated Paperboard 瓦楞紙板含蠟量試驗法 |
Translated |
|
|
CNS 15524-4
2017 Edition Plastics - Determination of ash - Part 3: Unplasticized cellulose acetate 塑膠－灰分測定法－第4部：聚醯胺 |
|
|
|
CNS 6097
2017 Edition Underfloor Ducts(Steel) 鋼製地板電線槽 |
|
|
|
CNS 4609
2017 Edition Double End Studs 雙端螺樁 |
|
|
|
CNS 15625-1
2017 Edition Paragliding equipment – Paragliders – Part 1: Requirements and test methods for structuraL strength 飛行傘設備─飛行傘─第1部：結構強度要求與試驗法 |
|
|
|
CNS 8481
2017 Edition Hydraulic Clutch Operating Cylinders for Automobiles 汽車用液壓離合器操作缸總成 |
Translated |
|
|
CNS 5969
2017 Edition Bronze Flanged Globe Valves (10kgf/c㎡) 青銅凸緣型球形閥（10 kgf/㎠） |
|
|
|
CNS 11363
2017 Edition Hop - Dip Aluminium Coated SteeL Wires 熱浸鍍鋁鋼線 |
|
|
|
CNS 6146
2017 Edition Method of Test for ElectromechanicaL Switches(General Rules) 電機開關檢驗法–總則 |
|
|
|
CNS 4124
2017 Edition Type A3 standard test block for ultrasonic angle beam testing 超音波斜束檢測用Ａ３型標準規塊 |
|
|
|
CNS 4762
2017 Edition Method of 5 Percent Sulfuric Acid Test for Stainless Steels 不銹鋼之５％硫酸腐蝕試驗法 |
|
|
|
CNS 5773
2017 Edition Thermistor Rods, Non - Insulated (Style TRX) 管形無絕緣熱敏電阻器（型號ＴＲＸ） |
|
|
|
CNS 8397
2017 Edition Stainless steeL wires for spring 彈簧用不銹鋼線 |
|
|
|
CNS 4708
2017 Edition Plastic drinking straw 直流用塑膠膜電容器（特牲Ｍ） |
Translated |
|
|
CNS 8065
2017 Edition DentaL handpieces-coupling dimensions 牙科用手機接頭尺度 |
|
|
|
CNS 3623
2017 Edition Basic EnvironmentaL Testing Procedures Part 2:Tests,Test Ca:Damp Heat,Steady State 環境試驗法（電氣、電子）–濕熱（穩態）試驗 |
Translated |
|
|
CNS 177
2017 Edition Flat Fitted Key and Its Seat (for CylindricaL Shaft End) 配合平鍵及槽（用於柱軸梢） |
|
|
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 14136
2017 Edition Method of ultrasonic test for steeL forgings 鍛鋼品超音波檢測法 |
|
|
|
CNS 7048
2017 Edition Method of Determination for Dimensios of Thermoplastic Pipe and Fittings 熱塑性塑膠管及配件之尺寸測定法 |
|
|
|
CNS 4256
2017 Edition Inter-locking Side Milling Cutters 扣聯側銑刀 |
Translated |
|
|
CNS 10839
2017 Edition Chromaticity Classification of Fluorescent Lamps 螢光燈管之色度分類 |
|
| Find out:14127Items | To Page of: First -Previous-Next -Last | [314] [315] [316] [317] [318] [319] [320] |
