"Part " CNS Standards List |
|
CNS 15449-2-101
2019 Edition Safe requirements for electrical for measurement, control and laboratory use ? Part 2-101: Particular requirements for in vitro diagnostic (IVD) medical equipment 量測、控制及實驗室使用電氣設備安全規定－第2-101 部:體外診斷(IVD)醫用設備之個別規定 |
|
|
|
CNS 15760-3
2019 Edition Footwear − General test methods – Part 3: Ageing conditioning 鞋類－一般試驗法－第3 部：老化調節 |
|
|
|
CNS 13306-1-5
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-5: Radio disturbance and immunity measuring apparatus - Antenna calibration test sites for 30 MHz to 1000 MHz 射頻擾動和免疫力量測設備與量測方法－第１－５部：射頻擾動和免疫力量測設備－30 MHz至 1000 MHz之天線校正場地 |
|
|
|
CNS 62933-4-1
2019 Edition Electrical energy storage systems (EESS) − Part 4-1: Guidance on environmental issues − General specification 電能儲存系統(EESS)－第4-1 部：環境議題之指引－一般規定 |
|
|
|
CNS 15125-1
2019 Edition Solar heating - Domestic water heating systems - Part 1 : Performance rating procedure using indoor test methods 太陽能加熱－家用熱水系統－第１部：性能評比程序之室內試驗法 |
|
|
|
CNS 15776-2
2019 Edition Energy management system application program interface (EMS-API) – Part 2: Glossary 能源管理系統應用程式介面－第2部：詞彙 |
|
|
|
CNS 15207-1
2019 Edition Road vehicles − Component test methods for electrical disturbances from narrowband radiated electromagnetic energy − Part 1: General principles and terminology 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第1 部:通則及用語 |
|
|
|
CNS 15200-9-1
2019 Edition Methods of test for paints – Part 9-1: Coating powders – Determination of gel time of thermosetting coating powders at a given temperature 塗料一般試驗法－第9-1 部：粉體塗料－指定溫度下熱固性粉體塗料膠化時間測定 |
|
|
|
CNS 15753
2019 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PP) − Part 7: Guidance for the assessment of conformity 地下排水及排污非壓力塑膠配管系統－聚乙烯(PE) |
|
|
|
CNS 15593-51
2019 Edition Electricity metering – Data exchange for meter reading, tariff and load control – Part 51: Application layer protocols 電力計量－讀表、計費及負載控制之資料交換－第51 部：應用層協定 |
|
|
|
CNS 14432-2
2019 Edition Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions − Method by analysis of evolved carbon dioxide − Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test 塑膠材料在控制堆肥條件下最終好氧生物分解度測定法－二氧化碳釋出量分析法－第2部：實驗室規模重量測定法 |
|
|
|
CNS 12514-7
2019 Edition Fire-resistance tests – Elements of building construction – Part 7: Specific requirements for columns 建築物構造構件耐火試驗法－第7 部：柱特定要求 |
|
|
|
CNS 15593-21
2019 Edition Electricity metering − Data exchange for meter reading, tariff and load control − Part 21: Direct local data exchange 電力計量－讀表、計費及負載控制之資料交換－第21 部：直接本地資料交換 |
|
|
|
CNS 15755-5-7
2019 Edition Conversion tables for units − Part 5-7: Pressure or stress − Kilopascal and millimeter of water 單位換算表－第5-7 部：壓力或應力－千帕斯卡與毫米水柱 |
|
|
|
CNS 61347-2-13
2019 Edition Lamp controlgear − Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules 光源控制裝置－第2-13部：LED模組用直流或交流電子式控制裝置之個別要求 |
|
|
|
CNS 62282-7-2
2019 Edition Fuel cell technologies − Part 7-2: Test methods − Single cell and stack performance tests for solid oxide fuel cells (SOFC) 燃料電池技術－第7-2部：試驗方法－固態氧化物燃料電池(SOFC)單電池及電池組性能試驗 |
|
|
|
CNS 15077-3
2019 Edition Test conditions for machining centres - Part 3 : Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis) 切削中心機之檢驗條件－第３部：具整合型分段指示或連續萬向分度頭之機器幾何檢驗（垂直Ｚ軸） |
|
|
|
CNS 15076-2
2019 Edition Modular units for machine tools - Workholding pallets - Part 2 : Workholding pallets of nominal size greater than 800 mm 工具機之模組單元－工件固定托板－第２部：標稱尺度８００ｍｍ以上之工件固定托板 |
|
|
|
CNS 15646-2
2019 Edition Rigid cellular plastics – Determination of flexural properties – Part 2: Detrmination of flexural strength and apparent flexural modulus of elasticity 硬質發泡塑膠－彎曲性能測定法－第2 部：彎曲強度與視彎曲彈性係數測定法 |
|
|
|
CNS 60245-7
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − Part 7: Heat resistant ethylene-vinyl acetate rubber insulated ables 額定電壓450/750 V 以下橡膠絕緣電纜－ 第7部：耐熱乙烯-醋酸乙烯酯橡膠絕緣電纜 |
|
|
|
CNS 16083-2
2019 Edition Viscosity and viscometric fixed points of glass − Part 2: Determination of annealing point and strain point by fiber elongation 玻璃黏度和黏度固定點－第2部：以玻璃絲拉伸法測定退火點和應變點 |
|
|
|
CNS 15659-2
2019 Edition Evaluation of moisture-absorbing and quick-drying properties in textiles − Part 2: Moisture management test 紡織品吸濕速乾性能評估－第2 部：水分傳導試驗法 |
|
|
|
CNS 15646-1
2019 Edition Rigid cellular plastics – Determination of flexural properties – Part 1: Basic bending test 硬質發泡塑膠－彎曲性能測定法－第1 部：基本彎曲試驗 |
|
|
|
CNS 15590-5
2019 Edition Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners with specified hardness classes – Coarse thread and fine pitch thread 碳鋼及合金鋼結件之機械性質－第5 部：規定硬度級數之固定螺釘及類似螺紋結件－粗螺紋及細螺紋 |
|
|
|
CNS 14545-5
2019 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 1:Glow-wire end-product test and guidance 火災危險性試驗－第２部：試驗方法－第１章／第１單元：完成品之熾熱線試驗及指引 |
|
|
|
CNS 16093-3
2019 Edition Welding and allied processes − Types of joint preparation − Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys 銲接及其相關製程－接頭準備型式－第3部：鋁及鋁合金的惰氣遮護金屬電弧銲接及惰氣遮護鎢極電弧銲接 |
|
|
|
CNS 14873-3
2019 Edition Road vehicles - Airbag components - Part 3: Testing of inflator assemblies 道路車輛－氣囊組件－第３部：充氣器 |
|
|
|
CNS 13306-2-2
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-2: Methods of measurement of disturbances and immunity - Measurement of disturbance power 射頻擾動和免疫力量測設備與量測方法－第２－２部：擾動和免疫力量測方法－擾動功率量測 |
|
|
|
CNS 7779-3
2019 Edition Industrial fans – Determination of fan sound power levels under standardized laboratory conditions − Part 3: Enveloping surface methods 工業用風機－在標準化實驗室條件下風機聲功率位準測定－第3 部：包絡面法 |
|
|
|
CNS 13306-2-4
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-4: Methods of measurement of disturbances and immunity - Immunity measurements 射頻擾動和免疫力量測設備與量測方法－第２－４部：擾動和免疫力量測方法－免疫力量測 |
|
| Find out:2535Items | To Page of: First -Previous-Next -Last | [25] [26] [27] [28] [29] [30] [31] |
