"D " CNS Standards List |
|
CNS 4102
2017 Edition Pliers anD nippers - Methods of test 夾鉗與剪鉗－多滑節轉樞夾鉗（水泵鉗） |
|
|
|
CNS 15466
2017 Edition Testing methoD of performance for air source heat pump water heaters 空氣源式熱泵熱水器之性能試驗法 |
|
|
|
CNS 6678
2017 Edition Essential oils - Determination of carbonyl value - Free hydroxylamine method 精油－羰值測定法（自由羥胺法） |
|
|
|
CNS 2774
2017 Edition UnbleacheD softwood sulfate pulp (USKP) 未漂白針葉樹硫酸鹽木漿 |
|
|
|
CNS 5153
2017 Edition Photography-Processing chemicals-Specifications for potassium bromiDe 照相術─顯像處理化學品─溴化鉀規格 |
|
|
|
CNS 11573
2017 Edition MethoD of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-50 Sand and Dust Test) 頻率３ＭＨｚ以下電連接器檢驗法（細砂與塵埃試驗ＴＰ–５０） |
|
|
|
CNS 130
2017 Edition Morse Taper Gauge, Without Flat HeaD 莫氏圓錐量規（無扁頭） |
|
|
|
CNS 9109
2017 Edition Symbols of Wiring of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖配線類符號 |
|
|
|
CNS 13650
2017 Edition Lot-Control Testing for Laser Diode(for Communication) 通信用雷射二極體之批品質控制測試 |
|
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with Sphericall OutsiDe Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 5516
2017 Edition InDuction Type Overcurrent Relay for High Voltage Receiving 高壓受電用感應式過電流電譯 |
|
|
|
CNS 11900
2017 Edition FixeD Ceramic Capacitors for Electronic Equipment (Semiconductor) 電子設備用陶瓷固定電容器（半導體） |
Translated |
|
|
CNS 11829
2017 Edition Light Emitting Diodes (for Indication) 發光二極體(指示用) |
|
|
|
CNS 15347
2017 Edition Safety of machinery − General principles for Design − Risk assessment and risk reduction 機械安全－設計之一般原則－風險評鑑及風險降低 |
|
|
|
CNS 14642
2017 Edition MethoDs of test for anions in highly purified water 超純水中陰離子之試驗法 |
|
|
|
CNS 2178
2017 Edition LiquiD Membrane-Forming Compounds for Curing Concrete 混凝土用液膜養護劑 |
Translated |
|
|
CNS 9621-3
2017 Edition Rubber hoses for liquefieD petroleum gases (LPGs) - Part 3: Dispensing hoses and hose assemblies 液化石油氣用橡膠管(LPG橡膠管)－第3部：加氣用管及管組合件 |
|
|
|
CNS 853
2017 Edition Cross Joints With QuaDri - Flange (Working Pressure Less Than 16 kgf/c㎡) 凸緣十字管接頭（使用壓力16 kgf/㎠） |
|
|
|
CNS 13594
2017 Edition MethoDs of Test for Loss of Thickness by Loading of Textile Floor Coverings 纖維製地毯類織物承受載重之厚度減少試驗法 |
|
|
|
CNS 6153
2017 Edition MethoD of Test for Electromechanical Switches(Mechanical Endurance) 電機開關檢驗法–機械耐久性 |
|
|
|
CNS 11355
2017 Edition Bronze ScreweD Ball Valves (10 kgf/c㎡) 青銅螺紋型球閥（ 10 kgf/㎠ ） |
|
|
|
CNS 538
2017 Edition Inspection Plug Gauge for Metric ThreaD Ring Gauge (Go End Limit, Fine, Medium and Coarse Fits) 公制螺紋樣圈之量柱及磨損量柱（通過端，精配，中配及粗配） |
|
|
|
CNS 10901
2017 Edition MethoD of Test for Terminal Blocks for Industrial and Similar Use 工業用接線板檢驗法 |
|
|
|
CNS 5052
2017 Edition Single Coil Spring Lock Washers for CylinDrical Head Screws 單圈彈簧墊圈（柱頭螺釘用） |
|
|
|
CNS 15551-3
2017 Edition Ergonomics - Accessible Design - Specification of age-related luminance contrast for coloured light 人因工程－無障礙設計 - 與年齡相關之色光照度對比規範 |
|
|
|
CNS 15550
2017 Edition GuiDelines for standards developers to address the needs of older persons and persons with disabilities 標準發展者考量年長者與 身心障礙者需求之指導綱要 |
|
|
|
CNS 228
2017 Edition 60° Center Drills，Straight Form with Conical Protective Chamfer 中心鑽（60°，去角直線錐形） |
Translated |
|
|
CNS 15481-3
2017 Edition RoaD vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads 道路車輛－電機電子配備環境條件與試驗－第３部：機械負載 |
|
|
|
CNS 9103
2017 Edition Symbols of Relays of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電驛類符號 |
|
|
|
CNS 6151
2017 Edition MethoD of Test for Electromechanical Switches(Overload) 電機開關檢驗法–過負荷 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [270] [271] [272] [273] [274] [275] [276] |
