"D " CNS Standards List |
|
CNS 6151
2017 Edition MethoD of Test for Electromechanical Switches(Overload) 電機開關檢驗法–過負荷 |
|
|
|
CNS 7664
2017 Edition MethoD of Test for Low Frequency (Below 3 MHz)Electrical Connectors (TP - 25 Probe Damage Test) 頻率３ＭＨｚ以下電連接器檢驗法（探針損壞試驗ＴＰ–２５） |
|
|
|
CNS 13418
2017 Edition MethoD of Test for Brightness for Mineral Fillers and Pigments for Paper Making (45° / 0° Directional Tester) 造紙用礦物質填料及顏料白度試驗法（４５° ／０°定向白度計法） |
Translated |
|
|
CNS 5268
2017 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 13650
2017 Edition Lot-Control Testing for Laser Diode(for Communication) 通信用雷射二極體之批品質控制測試 |
|
|
|
CNS 13652
2017 Edition Reliability Testing for Light Emitting Diode(for Communication) 通信用發光二極體之可靠度測試 |
|
|
|
CNS 4610
2017 Edition ThreaDed Rods 螺紋桿 |
|
|
|
CNS 11446-6
2017 Edition MethoDs of measurement on receivers for television broadcast transmission - Part 6 : Measurement under conditions different from broadcast signal standards 電視廣播傳輸接收機之量測方法-第6部 : 不同於廣播信號標準條件之量測 |
|
|
|
CNS 210
2017 Edition Short Drills with Square Taper Shank 方錐柄短鑽頭 |
Translated |
|
|
CNS 14656
2017 Edition Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering method in an essentially free field over a reflecting plane 聲學─測定噪音源聲功率位準的工程級方法─用於一反射平面上的自由聲場條件 |
|
|
|
CNS 14715
2017 Edition Electric resistance welDing－Integrated transformers for welding guns 工業用機器人電阻銲接—銲槍之變壓器 |
|
|
|
CNS 11360
2017 Edition ColD-rolled steel strips for springs 彈簧用冷軋鋼帶 |
|
|
|
CNS 12865-5
2017 Edition MethoD of Test for Digital Microelectronics ( Output Short Circuit Current ) 數位微電子檢驗法（輸出端短路電流） |
|
|
|
CNS 12866
2017 Edition Basic Environmental Testing ProceDures Part 2 : Tests-Test Z/AM : Combined Cold/Low Air Pressure Tests 環境試驗法（電氣、電子）–低溫／低氣壓複合試驗法 |
|
|
|
CNS 13649
2017 Edition Reliability Testing for Laser Diode(for Communication) 通信用雷射二極體之可靠度測試 |
|
|
|
CNS 12882
2017 Edition MethoD of Test for Hook Drawing Resistance of Cement Sack Paper Laminated with Plastic Woven Sheet 塑膠編織貼合水泥袋紙鈎裂強度試驗法 |
Translated |
|
|
CNS 14801
2017 Edition MethoD of test for water resistance of material used in protective clothing (Impact penetration test) 防護衣材料防水性試驗法－衝擊穿透試驗 |
|
|
|
CNS 1254
2017 Edition CanneD pickled vegetables 醬菜類罐頭 |
|
|
|
CNS 11358
2017 Edition Portable LeaD Storage Batteries ( replaced by CNS 6034 ) 氣動往復式手提木工鋸 |
|
|
|
CNS 3634
2017 Edition Basic Environmental Testing ProceDures,Part 2 : Tests, Test B : Dry Heat 環境試驗方法（電氣、電子）–高溫（耐熱性）試驗方法 |
|
|
|
CNS 7197
2017 Edition Basic Dimensions of 5 kgf/㎠ Ferrous Materials Pipe Flanges 鐵金屬製管凸緣基準尺度（5 kgf/㎠） |
|
|
|
CNS 4371
2017 Edition RounD Thread with Clearance and Steep Flank with Pitch 7 mm Theoretic Values 圓螺紋（具有間隙、深螺腹、螺距為７ｍｍ之理論值） |
|
|
|
CNS 15496
2017 Edition MethoDs of thickness measurement for sprayed coatings 熔射塗層厚度試驗法 |
|
|
|
CNS 4763
2017 Edition MethoD of ferric sulfate-sulfuric acid test for stainless steel 不銹鋼之硫酸鐵-硫酸溶液腐蝕試驗法 |
|
|
|
CNS 14335-2-3
2017 Edition Luminaires − Part 2-3: Particular requirements – Luminaires for roaD and street lighting 燈具－第2-3部：道路及街道照明用燈具之個別要求 |
|
|
|
CNS 6135
2017 Edition Hearing aiDs-Part 0:Measurement of electroacoustical characteristics 助聽器－第０部:電聲特性的量測 |
|
|
|
CNS 15550
2017 Edition GuiDelines for standards developers to address the needs of older persons and persons with disabilities 標準發展者考量年長者與 身心障礙者需求之指導綱要 |
|
|
|
CNS 10225
2017 Edition Test CoDe for Accuracy of Drum Sanders 圓筒砂光機精度檢驗標準 |
|
|
|
CNS 5376-6
2017 Edition Iron ores—MethoD for determination of acid soluble iron （Ⅱ）content 鐵礦石－酸可溶性鐵（Ⅱ）定量法 |
|
|
|
CNS 5283
2017 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度（齒廓面元線誤差之公差） |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [267] [268] [269] [270] [271] [272] [273] |
