"M " CNS Standards List |
|
CNS 6152
2017 Edition Method of Test for Electromechanical Switches(Electrical Endurance) 電機開關檢驗法–電耐久性 |
|
|
|
CNS 5772
2017 Edition TherMistor Disks, Insulated (Style TDC) 盤形絕緣熱敏電阻器（型號ＴＤＣ） |
|
|
|
CNS 3830
2017 Edition High Manganese Steel Castings 高錳鋼鑄鋼件 |
Translated |
|
|
CNS 4363
2017 Edition Slotted Countersunk (Flat) Head Screws for Fine Mechanics M 0.4 to M 1.4 精密用有槽平頂埋頭螺釘（標稱直徑自0.4mm至1.4mm） |
|
|
|
CNS 10461-1
2017 Edition Method of test for water repellency of textile fabrics - Bundesmann rain-shower test 織物撥水性試驗法－雨淋試驗 |
|
|
|
CNS 11829
2017 Edition Light EMitting Diodes (for Indication) 發光二極體(指示用) |
|
|
|
CNS 9621-3
2017 Edition Rubber hoses for liquefied petroleuM gases (LPGs) - Part 3: Dispensing hoses and hose assemblies 液化石油氣用橡膠管(LPG橡膠管)－第3部：加氣用管及管組合件 |
|
|
|
CNS 12846
2017 Edition HeliuM Mass Spectrometer Leak Testing by Trace Probe Method 氦質譜儀示蹤氣探針探漏法 |
|
|
|
CNS 7377
2017 Edition SeaMless Steel Tubes for High Pressure Gas Cylinder 高壓貯氣瓶用無縫鋼管 |
Translated |
|
|
CNS 4301
2017 Edition Test Code for Accuracy of Surface Grinding Machines with Vertical Grinding Wheel Spindle and Rotary Table 旋轉床台型立式平面磨床精度檢驗標準 |
|
|
|
CNS 517
2017 Edition Metric Buttress Screw Thread, Allowance and Tolerance 公制鋸齒形螺紋（裕度及公差） |
|
|
|
CNS 15077-10
2017 Edition Test conditions for Machining centres - Part 10: Evaluation of thermal distortions 切削中心機之檢驗條件－ 第10部：熱變形之評估 |
|
|
|
CNS 14801
2017 Edition Method of test for water resistance of material used in protective clothing (Impact penetration test) 防護衣材料防水性試驗法－衝擊穿透試驗 |
|
|
|
CNS 258
2017 Edition Ring Gauge for ReaMer 鉸刀校驗樣圈 |
|
|
|
CNS 14369
2017 Edition Micrographics-Reader-printers for transparent microforms-Characteristics 微縮技術－透明微縮品閱讀影印機－特性 |
|
|
|
CNS 5279
2017 Edition DiMensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 14489
2017 Edition Manipulating industrial robots-Presentation of characteristics 工業用機器人-特性之標示 |
|
|
|
CNS 14623-2
2017 Edition Sterilization of health care products-cheMical indicators-Part 2：Test equipment and methods 保健產品之滅菌─化學指示劑─第二部分：測試設備與方法 |
|
|
|
CNS 13594
2017 Edition Methods of Test for Loss of Thickness by Loading of Textile Floor Coverings 纖維製地毯類織物承受載重之厚度減少試驗法 |
|
|
|
CNS 14137
2017 Edition Method of eddy current test for titanium pipes and tubes 鈦管渦電流檢測法 |
|
|
|
CNS 13621
2017 Edition PolyaMide (Nylon) Textured Yarns 聚醯胺樹脂接線盒 |
Translated |
|
|
CNS 14613
2017 Edition 1800 MHz GSM mobile telephone system - Air interface １８００ＭＨｚＧＳＭ行動電話系統－空中介面 |
|
|
|
CNS 14179
2017 Edition Reliability tests for digital transMitter and receiver modules used for optical fiber communication 光纖通信用數位傳輸和接收模組之可靠度測試 |
|
|
|
CNS 124
2017 Edition Metric Taper for Tools 4-200 (Without Flat End) 工具圓錐（公制圓錐４–２００）（無扁頭） |
|
|
|
CNS 12291
2017 Edition General Rules for Reliability Assured Fixed Carbon CoMposition Resistors 可靠度保證混合碳固定電阻器總則 |
|
|
|
CNS 9240
2017 Edition Method of Test for Low Freguency(Below 3 MHz) Electrical Connectors(TP - 18 Visual and Dimensional Inspection) 頻率３ＭＨｚ以下電連接器檢驗法（外觀及尺度檢查ＴＰ–１８） |
|
|
|
CNS 3983
2017 Edition Method of Test for Mechanical Properties of Tapping Screws 自攻螺釘之機械性質檢驗法 |
Translated |
|
|
CNS 4421
2017 Edition Seating Bolts and Conical Spring Washers for ClaMping 夾緊用座螺栓與錐形彈簧墊圈 |
|
|
|
CNS 12664
2017 Edition Method of Test for Qualification Procedure of Welding Technique of Plastics 鑑定熔接塑膠技術之試驗法 |
|
|
|
CNS 4573
2017 Edition Slotted Raised Countersunk Bolts for Drawing InstruMents 有槽扁圓頂埋頭螺栓（繪圖儀器用） |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [265] [266] [267] [268] [269] [270] [271] |
