"S " CNS Standards List |
|
CNS 14332
2018 Edition Information technology-Programming languageS-CCITT high level language (CHILL) 資訊技術－程式語言－通訊用高階語言 |
|
|
|
CNS 2773
2018 Edition Coating filmS for metal cans of foods 食品用金屬空罐塗膜 |
|
|
|
CNS 15697
2018 Edition Wood – Determination of decay reSistance 木材耐腐朽性試驗法 |
|
|
|
CNS 16040
2018 Edition Footwear − Performance requirementS for components for footwear − Accessories 鞋類－鞋類組件性能要求－配件 |
|
|
|
CNS 15710-1
2018 Edition EffectS of current on human beings and livestock − Part 1: General aspects 電流在人體及家畜上之效應－第1 部：概觀 |
|
|
|
CNS 17190-4
2018 Edition Urine-abSorbing aids for incontinence − Test methods for characterizing polymer-based absorbent materials − Part 4: Determination of moisture content by mass loss upon heating 尿失禁用尿液吸收輔具－聚合物吸收材料特性試驗法－第4部：以加熱質量損失法測定含水量 |
|
|
|
CNS 9274
2018 Edition Hot-rolled Steel plate, sheet and strip for automobile structural uses 汽車結構用熱軋鋼板、鋼片及鋼帶 |
|
|
|
CNS 12238
2018 Edition Air cargo equipment − BaSe-restrained certified containers exclusively for the lower deck of large-capacity aircraft 空運貨櫃－廣體機下貨艙底盤受制認可貨櫃 |
|
|
|
CNS 4534
2018 Edition TermS of fasteners for screws,bolts,studs 結件詞彙（螺釘、螺栓、螺樁） |
|
|
|
CNS 61121
2018 Edition Tumble dryerS for household use − Methods for measuring the performance 家用滾筒式乾衣機－性能量測法 |
|
|
|
CNS 11199
2018 Edition Pneumatic tyreS terms and definitions 鐵路車輛用氣壓式車窗雨刷器 |
|
|
|
CNS 15144
2018 Edition Dried meat product 乾燥肉品 |
|
|
|
CNS 5064
2018 Edition MethodS of Luminance Measurements 輝度測量法 |
|
|
|
CNS 16000-23
2018 Edition Indoor air – Part 23: Performance teSt for evaluating the reduction of formaldehyde concentrations by sorptive building materials 室內空氣－第23部：評估吸附/吸收性建築材料降低甲醛濃度之性能試驗 |
|
|
|
CNS 13358
2018 Edition Microwave Therapy Equipment 微波治療器 |
|
|
|
CNS 4187
2018 Edition FaSteners 打包鐵皮扣 |
|
|
|
CNS 8963
2018 Edition Marine BraSs 30 kgf/㎠ Stop Valves with Bite Joint(S) 船用黃銅停止閥附咬接接頭（30 kgf/㎠） |
|
|
|
CNS 16036
2018 Edition Safety of machinery − Equipment for power driven parking of motor vehicles − Safety and EMC requirements for design, manufacturing, erection and commissioning stages 機械安全－機動車輛之動力驅動停車設備－設計、製造、安裝及試運轉階段之安全與電磁相容要求 |
|
|
|
CNS 1792
2018 Edition MagneSium Perchlorate, Anhydrous 化學試藥（過氯酸美，無水） |
|
|
|
CNS 10078
2018 Edition DiStribution Boards (Simple Type, Below 125V) for Marine Use 船用分電箱（簡易型，１２５Ｖ以下） |
|
|
|
CNS 4337
2018 Edition Canned Snail meat 蝸牛肉罐頭 |
|
|
|
CNS 10454
2018 Edition Method of teSt for distillation of emulsified bitumen 乳化瀝青蒸餾試驗法 |
|
|
|
CNS 9698
2018 Edition Jumper CouplerS 電氣連結器 |
|
|
|
CNS 9550
2018 Edition TailorS Shears 裁縫用鋼製剪刀 |
Translated |
|
|
CNS 14175
2018 Edition B-ISDN ATM adaptation layer - Service specific coordination function for signalling at the network node interface (SSCF at NNI) 寬頻整體服務數位網路非同步傳送模式調適層–網路節點介面信號用服務特定協調功能 |
|
|
|
CNS 11613
2018 Edition Electric Heating Appliance (InStantaneous Heating Type) with Using Water Resistance to Limit the Current to Ground 家庭用水電阻接地式電熱水器（瞬熱型） |
Translated |
|
|
CNS 4982
2018 Edition Advance-warning triangleS 預警三角標誌牌 |
|
|
|
CNS 16063
2018 Edition Textile fabricS − Burning behaviour − Measurement of flame spread properties of vertically oriented specimens 紡織品織物－燃燒行為－試樣垂直方向火焰延燒性質試驗法 |
|
|
|
CNS 12396
2018 Edition Signal Quality at Interface Between Data Terminal Equipment and Synchronous Data Circuit-Terminating Equipment for Serial Data Transmission 串列資料傳輸用資料終端設備與同步資料電路終端設備間介面上之信號品質 |
|
|
|
CNS 15565-1
2018 Edition Ergonomic deSign for the safety of machinery – Part 1: Principles for determining the dimensions required for openings for whole-body access into machinery 機械安全之人因工程設計－第1部：人員全身進入機械內 的開口所需尺度之決定原則 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [260] [261] [262] [263] [264] [265] [266] |
