"S " CNS Standards List |
|
CNS 15247
2018 Edition TeSt methods on light emitting diode components and modules (for general lighting service) for normal life 照明用發光二極體元件與模組之一般壽命試驗方法 |
Translated |
|
|
CNS 15705-2
2018 Edition ToolS for pressing – Punch holder shanks – Part 2: Type C 衝壓用工具－衝頭座柄－第2 部：C 型 |
|
|
|
CNS 14326
2018 Edition Digital Subscriber signalling system no.2 - Connection characteristics negotiation during call/connection establishment phase 第二號數位用戶信號系統－呼叫／連接建立階段中之連接特性協商 |
|
|
|
CNS 5744
2018 Edition Half - Hard - Drawn Aluminium WireS for Electric Purposes 電機用半硬鋁線 |
Translated |
|
|
CNS 10915
2018 Edition Level RecorderS for Recording Sound Level and/or Vibration Level 聲度、振動位準記錄用位準記錄器 |
|
|
|
CNS 12408
2018 Edition Information technology - Automatic identification and data capture techniqueS - EAN/UPC bar code symbology specification 資訊技術－自動識別與資料擷取 技術－EAN/UPC條碼符號表示法 |
|
|
|
CNS 15569-1
2018 Edition Hydraulic fluid power - Filter elementS - Part 1: Verification of collapse/burst pressure rating 液壓流體動力－過濾器濾心－第1部：查證崩潰/爆裂壓力額定值 |
|
|
|
CNS 3507
2018 Edition Stainless steel covered electrodes 不銹鋼被覆銲條 |
|
|
|
CNS 10495
2018 Edition Hammering TeSt Device of Carbon Steel Tyres for Railway Rolling Stock 鐵路車輛用碳鋼輪箍落重試驗裝置 |
|
|
|
CNS 11205
2018 Edition Oil Seals for Railway Rolling Stock 鐵路車輛用油封 |
|
|
|
CNS 15590-7
2018 Edition Mechanical propertieS of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 3-5
2018 Edition Engineering Drawing(Symbols for Riveting) 工程製圖（鉚接符號） |
|
|
|
CNS 14358
2018 Edition Information technology-Open Systems interconnection-Application layer structure 資訊技術－開放系統互連－應用層結構 |
|
|
|
CNS 2963
2018 Edition Method of TeSt for the Life of Electric Heating Wire and Ribbon 電熱線與電熱帶壽命試驗方法 |
|
|
|
CNS 10077
2018 Edition Section Board (Simple Type, Below 125V) for Marine Use 船用區電箱（簡易型，１２５Ｖ以下） |
|
|
|
CNS 10434
2018 Edition CaSt Steel Cargo Blocks with Roller Bearings for Marine Use 船舶吊貨用鑄鋼滑車（附滾子軸承） |
|
|
|
CNS 14952-2
2018 Edition Guide for the determination of thermal endurance propertieS of electrical insulating materials - Part 2: Choice of test criteria 電氣絕緣材料之耐熱性測定指引－第２部：試驗準則之選定 |
|
|
|
CNS 3-13
2018 Edition Engineering Drawing (Geometrical Tolerancing - PoSitional Tolerancing) 工程製圖（幾何公差–位置度公差之標註） |
|
|
|
CNS 15652-4
2018 Edition Intelligent lighting Systems − Part 4: Design guide for field area network 智慧照明系統－ 第4部：場域網路設計指引 |
|
|
|
CNS 5749
2018 Edition Rectangular Copper WireS for Electrical Purposes 矩形銅線 |
|
|
|
CNS 12701
2018 Edition TeSt method for flexural strength (modulus of rupture) of fine ceramics at room temperature 精密陶瓷室溫彎曲強度(破壞模數)試驗法 |
|
|
|
CNS 61347-2-9
2018 Edition Lamp controlgear − Part 2-9: Particular requirementS for ballast of discharge lamps (excluding fluorescent lamps) 光源控制裝置－第2-9部：放電燈(螢光燈除外)用感抗式安定器之個別要求 |
|
|
|
CNS 14153
2018 Edition TranSmission of non-telephone signals - A real time control protocol for simplex applications using the H.221 LSD/HSD/MLP channels 非電話信號之傳輸–使用６４至１９２０ｋｂｐｓ通道訊框結構之ＬＳＤ／ＨＳＤ／ＭＬＰ通道之單工應用即時控制協定 |
|
|
|
CNS 14393-8
2018 Edition Biological evaluation of medical deviceS - Part 8: Selection and qualification of reference materials for biological tests 醫療器材生物性評估－第８部：生物測試用參考材料之選擇及資格認定 |
|
|
|
CNS 6391
2018 Edition Method of teSt for meat and meat products - Determination of nitrate content 肉及肉製品檢驗法－硝酸鹽含量之測定 |
|
|
|
CNS 35
2018 Edition Standard Testing Temperature 標準檢測溫度 |
|
|
|
CNS 10365
2018 Edition Method of teSt for settlement and storage stability of emulsified bitumen 乳化瀝青靜置分離及儲存安定性試驗法 |
|
|
|
CNS 17190-4
2018 Edition Urine-abSorbing aids for incontinence − Test methods for characterizing polymer-based absorbent materials − Part 4: Determination of moisture content by mass loss upon heating 尿失禁用尿液吸收輔具－聚合物吸收材料特性試驗法－第4部：以加熱質量損失法測定含水量 |
|
|
|
CNS 14914
2018 Edition GuidelineS for TAGUCHI methods and their application 田口式品質工程與其應用指導綱要 |
|
|
|
CNS 15651-1
2018 Edition Energy performance of lamp controlgear − Part 1: Controlgear for fluoreScent lamps − Method of measurement to determine the total input power of controlgear circuits and the efficiency of the controlgear 光源控制裝置之能源效率－第1部： 螢光燈用控制裝置－光源-控制裝置電路 之總輸入功率與控制裝置效率之量測法 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [248] [249] [250] [251] [252] [253] [254] |
