"D " CNS Standards List| Method test | Rack Pionion | Rivet holding | Method Test | Biodegradable plastics | Household similar | Picks | Dropping Test | |
|
CNS 17966
2018 Edition Assistive proDucts for personal hygiene that support users − Requirements and test methods 支撐使用者之個人衛生輔具－要求及試驗法 |
|
|
|
CNS 11181
2018 Edition MethoD of Test for Enclosed Sensitive Switches 封閉型微動開關檢驗法 |
|
|
|
CNS 13540
2018 Edition PreblenDed dry mortar mix 預鑄混凝土電纜管組 |
|
|
|
CNS 15569-4
2018 Edition HyDraulic fluid power - Filter elements - Part 4: Method for end load test 液壓流體動力－過濾器濾心－第4部：端負載試驗法 |
|
|
|
CNS 3741
2018 Edition MethoD of Test for Glow Starters for Fluorescent Lamp 預熱型螢光燈管用輝光起動器檢驗法 |
|
|
|
CNS 14713
2018 Edition Information technology─Open system interconnection─The registration of object iDentifiers 資訊技術－開放系統互連－物件識別符之註冊 |
|
|
|
CNS 5315
2018 Edition The Test MethoDs of Panel Board Units 配電箱試驗法 |
|
|
|
CNS 13369-1
2018 Edition Office Machines - Minimum Information to be IncluDed in Specification Sheets Part 1: Duplicators 事務機器–規格書應包含的最少資訊 第１部: 複印機 |
|
|
|
CNS 1056
2018 Edition Low-voltage three-phase inDuction motors 低電壓三相感應電動機 |
Translated |
|
|
CNS 13692
2018 Edition Support of Packet MoDe Terminal Equipment by an Integrated Services Digital Network (ISDN) 整體服務數位網路所提供之分封式終端設備 |
|
|
|
CNS 1433-1
2018 Edition Hacksaw blaDes − Part 1: Dimensions for hand blades 鋸條－第1部：手弓鋸條之尺度 |
|
|
|
CNS 808
2018 Edition Rubber hoses, textile-reinforceD, for compressed air 壓縮空氣用織物強化橡膠管 |
|
|
|
CNS 4995
2018 Edition ReinforceD Concrete Manhole Blocks for Sewerage Work 下水道用鋼筋混凝土人孔井壁 |
Translated |
|
|
CNS 11997
2018 Edition Starters anD Controllers for A.C Motor in Ships 船用交流電動機用起動器及控制器 |
|
|
|
CNS 13990
2018 Edition Polyester-nylon EnameleD Copper Wires 聚乙烯絕緣聚氯乙烯被覆屋內電話電纜 |
|
|
|
CNS 12963
2018 Edition Decorated concrete blocks 裝飾混凝土磚 |
|
|
|
CNS 10609
2018 Edition MethoD of Test for Portable Electric Grinders 手提電磨機試驗法 |
Translated |
|
|
CNS 13360
2018 Edition Data Communication - 34 Pin DTE/DCE Interface Connector and pin Assignments 數據通訊–３４插腳ＤＴＥ／ＤＣＥ介面連接器及插腳配置 |
|
|
|
CNS 4670-3
2018 Edition SpecifieD Items for Machine Tools - Turret Lathes 工具機規範之項目–六角車床 |
Translated |
|
|
CNS 15605-2
2018 Edition Plastics − Determination of temperature of deflection under load − Part 1: General test method 塑膠－受負荷下之撓曲溫度測定法－第２部：塑膠與硬橡膠 |
|
|
|
CNS 10207
2018 Edition Exit lights anD emergency direction lights 出口標示燈及避難方向指示燈 |
|
|
|
CNS 16055
2018 Edition Personal eye-protection − InfrareD filters − Transmittance requirements and recommended use 個人眼睛防護－紅外線濾光鏡片－透光度要求及使用 |
|
|
|
CNS 11995
2018 Edition Spare Parts for Motor Starters anD Controllers in Ships 船用電動機起動器及控制器之備品供給基準 |
|
|
|
CNS 7081
2018 Edition LeaDs for mechanical pencils 自動鉛筆用筆芯 |
|
|
|
CNS 8495
2018 Edition Marine Cast Iron 5 kgf/㎠ Screw-Down Check Angle Valves 船用鑄鐵螺桿止回角閥（5 kgf/㎠） |
|
|
|
CNS 35
2018 Edition StanDard Testing Temperature 標準檢測溫度 |
|
|
|
CNS 6074
2018 Edition Steel Tape Armor anD Anti - Corrosive Layer for Electric Cable 電纜用鋼帶鎧裝及防蝕層 |
Translated |
|
|
CNS 6945
2018 Edition Debydrated Larval Fish, Chilled (Packaged) 冷藏魩仔魚脯 |
|
|
|
CNS 14907
2018 Edition MethoD of test for acid-insoluble lignin in wood 木材中酸不溶性木質素試驗法 |
|
|
|
CNS 15468-6-300
2018 Edition Fuel cell technologies − Part 6-300: Micro fuel cell power systems − Fuel cartriDge interchangeability 燃料電池技術－第6-300部：微型燃料電池發電系統－燃料匣之可互換性 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [215] [216] [217] [218] [219] [220] [221] |
