"m " CNS Standards List |
|
CNS 15609-1
2018 Edition Thermoplastics pipes and fittings − Vicat softening temperature − Part 1: General test method 熱塑性塑膠管與管件－衛氏軟化 溫度－第1部：一般試驗法 , |
|
|
|
CNS 13927
2018 Edition Information technology-Open systems interconnection-Systems management overview 資訊技術–開放系統互連–系統管理綜觀 |
|
|
|
CNS 14994
2018 Edition Packaging - Complete, filled transport packages and unit loads - Sinusoidal vibration tests using a variable frequency 包裝貨物與單位裝載之可變動頻率正弦波振動試驗法 |
|
|
|
CNS 4234-3
2018 Edition mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress 不銹鋼結件之機械性質－第３部：無拉應力下之固定螺釘及類似結件 |
|
|
|
CNS 4735-1
2018 Edition 50Ω and 75Ω radio-frequency coaxial cables Part 1：General requirements and measuring methods 50Ω及75Ω射頻同軸電纜－第1部：通則與測試方法 |
|
|
|
CNS 4339
2018 Edition method of Test for Determining Water Emersion Endurance of Glue Seams of Paper Sacks 紙袋膠縫耐水浸潤時間之試驗法 |
|
|
|
CNS 9136
2018 Edition 250V Single-Core, Twin-Core, Three-Core EPR Insulated CP Sheathed metal Netting Covered Cable (250V-SPNC, 250V-DPNC, 250V-TPNC) and PVC Anti-Corrosion Cable (250V-SPNCY, 250V-DPNCY, 250V-TPNCY) for Marine Use 船用２５０Ｖ單心、二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜及２５０Ｖ單心、二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜 |
|
|
|
CNS 1354
2018 Edition methed of test for tensile properties of paper and board (Pendulum mehod) 紙及紙板抗張性質試驗法（擺錘法） |
|
|
|
CNS 15562-4
2018 Edition Stationary training equipment − Part 4: Strength training benches, additional specific safety requirements and test methods 固定式訓練器材－第4部：肌力訓練台之附加特定安全要求與試驗法 |
|
|
|
CNS 15568
2018 Edition Protecting Equipment and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 13618
2018 Edition method of Test for Potential Alkali-Silica Reactivity of Aggregates(Chemical Method) 粒料之潛在鹼質與二氧化矽反應性試驗法（化學法） |
|
|
|
CNS 1382
2018 Edition method of Test for Formaldehyde of Industrial Grade 工業級甲醛檢驗法 |
|
|
|
CNS 15456
2018 Edition methods of measurement on alternating current light emitting diode components for optical and electrical characteristics 交流發光二極體元件之光學及電性量測法 |
|
|
|
CNS 14952-1
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials - Part 1: General guidelines for ageing procedure and evaluation of test results 電氣絕緣材料之耐熱性測定指引－第１部：老化程序與試驗結果評估之一般導引 |
|
|
|
CNS 14545-3
2018 Edition Fire hazard testing-part 1:Guidance for the preparation of requirements and test specifications for assessing fire hazard of electrotechnical products-Guidance for use of preselection procedures 火災危險性試驗－第１部：制定評估電氣產品之火災危險性需求及試驗內容之指引－預選程序之指引 |
|
|
|
CNS 4394-5
2018 Edition Plastics − Injection moulding of test specimens of thermoplastic materials − Part 4: Determination of moulding shrinkage 塑膠－熱塑性塑膠射出成型試片－第5部：研究異向性標準試片之製備 |
|
|
|
CNS 13862
2018 Edition message handling systems-remote operations and reliable transfer server 信息處理系統–遠程作業及可靠轉送伺服器 |
|
|
|
CNS 12737
2018 Edition Spiral Steel Forms for Hollow Slab 中空樓板用螺旋鋼製管模 |
Translated |
|
|
CNS 14952-3-2
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials – Part 3: Instructions for calculating thermal endurance characteristics – section 2: the calculation for incomplete data – verification for test result from gr 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第２章：不完整資料的計算－以包含中間時間到終止點之等量試驗群組驗證試驗結果 |
|
|
|
CNS 10062
2018 Edition Nominal Dimension of Veneer Jointers 薄板刨邊機之標稱尺度 |
|
|
|
CNS 14393-1
2018 Edition Biological evaluation of medical devices – Part 1：Evaluation and testing 醫療器材生物性評估－第一部分：評估與試驗 |
|
|
|
CNS 5064
2018 Edition methods of Luminance Measurements 輝度測量法 |
|
|
|
CNS 12397
2018 Edition Signal Quality for Transmitting and Receiving Data Processing Terminal Equipments Using Serial Data Transmission at the Interface with Non-Synchronous Data Circuit-Terminating Equipment 發送及接收資料處理終端設備與非同步資料電路終端設備介面串列資料傳輸之信號品質 |
|
|
|
CNS 15037-1
2018 Edition Walking aids manipulated by both arms - Requirements and test methods - Part 1: Walking frames 雙臂操作步行輔具－要求及測試法－第１部：助行器 |
|
|
|
CNS 12821-1
2018 Edition Identification Cards-Recording Technique-Part 1 : Embossing 識別卡（登錄技術第１部，壓刻） |
|
|
|
CNS 11794
2018 Edition minimum Length Between the Cable Entrances and the Terminals of Electric Machinery and Equipment for Marine Use 船用電器電纜導入口與端子間之最小尺度 |
|
|
|
CNS 9137
2018 Edition 250V Single-Core, Twin-Core Three-Core ERR Insulated PVE Sheathed Cable (250V-SPY, 250V-DPY, 250V-TPY) for marine Use 船用２５０Ｖ單心、二心、三心ＥＰＲ絕緣ＰＶＣ被覆電纜（２５０Ｖ–ＳＰＹ，２５０Ｖ–ＤＰＹ，２５０Ｖ–ＴＰＹ） |
|
|
|
CNS 11428
2018 Edition Watt-hour meter 瓦時計 |
Translated |
|
|
CNS 14637-3
2018 Edition Test code for machine tools − Part 3: Determination of thermal effects 工具機試驗規範－第3部：熱效應之決定 |
|
|
|
CNS 17050-1
2018 Edition Conformity assessment − Supplier's declaration of conformity − Part 1: General requirements 符合性評鑑－供應者之符合性聲明－第1 部：一般要求事項 |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [187] [188] [189] [190] [191] [192] [193] |
