"3 3 " CNS Standards List| Rubber Vibration | Bolted Connections | Certification method | Parallel Shank | Method test | Tool holders | Hearing aids | Codes the | |
|
CNS 3887
1993 Edition Method of Test for Heat Treatment of Bicycle Parts 自行車（腳踏車）零件熱處理檢驗法 |
Translated |
|
|
CNS 3884
1993 Edition Surface Treatment for Bicycle Parts 自行車（腳踏車）零件表面處理 |
Translated |
|
|
CNS 3885
1993 Edition Method of Test for Surface Treatment of Bicycle Parts 自行車（腳踏車）零件表面處理檢驗法 |
Translated |
|
|
CNS 13288
1993 Edition Basic Environmental Testing Procedures Part 2: Tests - Guidance on Change of Temperature Tests 環境試驗法（電氣、電子）－溫度變化試驗之指引 |
|
|
|
CNS 4432
1993 Edition Slotted Round Nuts 頂槽圓螺帽 |
|
|
|
CNS 3880
1993 Edition Method of Test for the Spokes of Bicycles 自行車（腳踏車）輻絲檢驗法 |
Translated |
|
|
CNS 13299
1993 Edition Method of Test for Trapezoid Tearing Strength of Geotextiles 地工織物撕裂強度試驗法（梯形法） |
|
|
|
CNS 13217
1993 Edition Cold Rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 冷軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 13253
1993 Edition Method of Inspection for Spot Welds 點熔接部之檢驗法 |
|
|
|
CNS 13252
1993 Edition Method of Tension Test for Spot Welded Joints 點熔接接合之拉伸試驗法 |
|
|
|
CNS 13267
1993 Edition Test Methods for Performance and Accuracy of Single Spindle Wood Borer 木工鑽孔機之性能試驗及精度檢驗法 |
|
|
|
CNS 13268
1993 Edition Test Methods for Performance and Accuracy of Moulding Machine 多軸鉋機之性能試驗及精度檢驗法 |
|
|
|
CNS 4433
1993 Edition Round Nuts With Set Pin Hole in Side 側孔圓螺帽 |
|
|
|
CNS 713
1993 Edition Cast iron flanged gate valves (10 kgf/㎠) (Inside screw non-rising stem type) 鑄鐵凸緣型閘閥(10 kgf/cm2)（閥桿非上升型） |
Translated |
|
|
CNS 5973
1993 Edition Cast Iron Flanged Angle Valves (10kgf/c㎡) 鑄鐵凸緣型角閥(10 kgf/cm2) |
|
|
|
CNS 3631
1993 Edition Basic Environmental Testing Procedures Part 2: Tests - Test Q: Sealing 環境試驗法（電氣、電子）－密封性試驗法 |
|
|
|
CNS 3633
1993 Edition Basic Environmental Testing Procedures Part 2: Tests, Test N: Change of Temperature 環境試驗法（電氣、電子）－溫度變化試驗 |
|
|
|
CNS 10378
1993 Edition Method of Test for Folding Endurance of Paper and Paperboard (MIT Tester) 紙及紙板耐折強度試驗法（MIT試驗機） |
Translated |
|
|
CNS 13198
1993 Edition Fixed Multilayer Ceramic Chip Capacitors for Use in Electronic Equipment 電子設備用固定多層陶瓷晶片電容器 |
|
|
|
CNS 13211
1993 Edition Audiovisual Equipment and System - Rating Plates - Marking of Electricity Supply 視聽設備與系統之電源供應額定值面板標示 |
|
|
|
CNS 13212
1993 Edition Surface Acoustic Wave (SAW) Resonators Part 1: General Information and Standard Values 表面聲波諧振器－第一部：一般性資訊及標準值 |
|
|
|
CNS 13166
1993 Edition Inspection for Flash Welds (Steel) 閃電熔接部之檢驗法（鋼） |
|
|
|
CNS 1326
1993 Edition Electrical Insulating Oils 電絕緣用油 |
Translated |
|
|
CNS 13214
1993 Edition Basic Environmental Testing Procedures Part 2: Tests – Test Ec: Drop and Topple, Primarily for Equipment - type Specimens 環境試驗法（電氣、電子）－面落下、角落下及翻倒（主要為設備）試驗法 |
|
|
|
CNS 3882
1993 Edition Coating for Bicycle Parts 自行車（腳踏車）零件塗裝 |
Translated |
|
|
CNS 13330
1993 Edition Dynamo Lamp for Bicycles 自行車（腳踏車）用發電燈 |
|
|
|
CNS 13216
1993 Edition Hot - rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 熱軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 11327
1993 Edition Submersible motor - Pumps for deep wells 深井用沈水電動機泵 |
Translated |
|
|
CNS 853
1993 Edition Cross Joints With Quadri - Flange (Working Pressure Less Than 16 kgf/c㎡) 凸緣十字管接頭(使用壓力16 kgf/cm2) |
|
|
|
CNS 739
1993 Edition Method of Test for Rubber Inner Tubes for Bicycles 自行車用橡膠內胎檢驗法 |
|
| Find out:6360Items | To Page of: First -Previous-Next -Last | [186] [187] [188] [189] [190] [191] [192] |
