"For " CNS Standards List |
|
CNS 6408
2017 Edition Calculation of Load Capacity For Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算–齒廓面作用帶因數Zн |
|
|
|
CNS 11226
2017 Edition Radiographic Test For Carbon Steel Weldment 碳鋼熔接件射線檢測法 |
|
|
|
CNS 14603
2017 Edition Use of apparatus For the determination of length change of hardened cement paste ,mortar ,concrete 硬固水泥砂漿及混凝土長度變化試驗法 |
|
|
|
CNS 11609
2017 Edition Method of Test For Unplasticized Polyvinyl Chloride Pipes with Fiberglass Reinforced Plastic Reinforcement 玻璃纖維強化塑膠加強聚氯乙烯塑膠硬質管檢驗法 |
Translated |
|
|
CNS 8910
2017 Edition Methods of exposure to laboratory light sources For polymeric material of buildings 建築用聚合材料實驗室光源曝露試驗法 |
|
|
|
CNS 13982-2
2017 Edition Methods of test For bulk down and feather − Part 2: Sampling 羽絨羽毛試驗法－第2部：抽樣 |
|
|
|
CNS 5770
2017 Edition General Specification For Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 14694-3
2017 Edition Audio , video and audiovisual systems- interconnections and matching values Part 3：Interface For the interconnection ENG cameras and portable VTRs using non-composite signals 聲音、影像及視聽系統之互連與匹配值－第３部：ＥＮＧ攝影機與可攜式ＶＴＲｓ使用非複合式信號互連之介面 |
|
|
|
CNS 5285
2017 Edition Accuracy of Cylindrical Gear Teeth Tolerance For Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 14645
2017 Edition Light gauge stainless steel pipe fittings For ordinary piping 一般配管用不銹鋼鋼管接頭 |
|
|
|
CNS 8784
2017 Edition Method of Test For Tensile of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管拉伸試驗法 |
|
|
|
CNS 444
2017 Edition Grading rules For sawn lumber 製材之分等 |
|
|
|
CNS 12896
2017 Edition Pressure Rating For Ferrous Material Pipe Flanges 氣體熔接、截割（切斷）用壓力調整器 |
|
|
|
CNS 5376-5
2017 Edition Iron ores—Methods For determination of total iron content 鐵礦石—總鐵定量法 |
|
|
|
CNS 11225
2017 Edition Liquid Penetrant Test For Castings 鑄件表面液滲檢驗法 |
|
|
|
CNS 5298
2017 Edition Hose Clamps For the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 6407
2017 Edition Calculation of Load Capacity For Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算-負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 4053-1
2017 Edition Unplasticized polyvinyl chloride (PVC-U) pipes For water supply 自來水用硬質聚氯乙烯塑膠管 |
Translated |
|
|
CNS 15563
2017 Edition Grading rules of softwood sawn lumber For furnishing use in building 針葉樹裝修用製材分等 |
|
|
|
CNS 6834-9
2017 Edition Testing methods For rubber and plastics hoses - Part 9: Bending properties of hoses and tubing 橡膠管及塑膠管試驗法－第9部：膠管及軟管之彎曲特性 |
|
|
|
CNS 11659
2017 Edition Method of Test For Construction Parts of Glassfiber Reinforced Plastic Septic Tank 玻璃纖維強化塑膠化糞槽體檢驗法 |
Translated |
|
|
CNS 3874
2017 Edition Method of Test For the Tire Valves of Bicycles 自行車（腳踏車）車胎空氣閥檢驗法 |
Translated |
|
|
CNS 11377
2017 Edition Magnetic Particle Test For Castings and Forgings 鑄件及鍛件磁粒檢驗法 |
Translated |
|
|
CNS 12298
2017 Edition Method of Test For Low Frequency (Below 3 MHz) Electrical Connectors (TP-53 Nitric Acid Vapor Test, Gold Finish) 頻率３ＭＨｚ以下電連接器檢驗法（硝酸氣試驗，鍍金接點ＴＰ–５３） |
|
|
|
CNS 3885
2017 Edition Method of Test For Surface Treatment of Bicycle Parts 自行車（腳踏車）零件表面處理檢驗法 |
Translated |
|
|
CNS 3882
2017 Edition Coating For Bicycle Parts 自行車（腳踏車）零件塗裝 |
Translated |
|
|
CNS 13020
2017 Edition Method of Radoigraphic Test For the Welds of Steel Structure 鋼結構銲道射線檢測法 |
|
|
|
CNS 11708
2017 Edition Method of Test For Land Mobile Communication FM or PM Transmitters, 25-470 MHz 陸上行動通信用２５–４７０ＭＨｚ調頻／調相發射機檢驗法 |
|
|
|
CNS 12865-7
2017 Edition Method of Test For Digital Microelectronics ( Drive Source, Dynamic ) 數位微電子檢驗法（驅動源，動態） |
|
|
|
CNS 7664
2017 Edition Method of Test For Low Frequency (Below 3 MHz)Electrical Connectors (TP - 25 Probe Damage Test) 頻率３ＭＨｚ以下電連接器檢驗法（探針損壞試驗ＴＰ–２５） |
|
| Find out:9607Items | To Page of: First -Previous-Next -Last | [181] [182] [183] [184] [185] [186] [187] |
