"S " CNS Standards List| Conformity assessment | Glossary Terms | Method Test | Terms relating | Glassfiber Reinforced | Natural Rubber | Finger Sack | Determination the | |
|
CNS 747
2019 Edition Flat rubber beltS for power transmission 動力傳動用平面橡膠帶 |
|
|
|
CNS 9487
2019 Edition Bronze Screw down Check Globe Valves for Marine Use (5 kgf / ㎠) (Union Bonnet Type) 船用青銅管套帽型螺桿止回球形閥（5 kgf/㎠） |
|
|
|
CNS 9383
2019 Edition Multi - ConnectorS Use in Electronics and Waterproof for Automotives 汽車電子用及防水用多根接頭 |
|
|
|
CNS 9846
2019 Edition Light Extinction Type Smokemeters for Diesel Automobiles 柴油車用透光式排氣煙度計 |
|
|
|
CNS 14486
2019 Edition Manipulating induStrial robots − Mechanical interfaces − Plates 工業用機器人－機械介面－板式 |
|
|
|
CNS 15737
2019 Edition Safety of primary and secondary lithium cells and batteries during transport 一次與二次鋰單電池及電池組運輸安全性 |
|
|
|
CNS 15200-1-5
2019 Edition TeSting methods for paints - Part 1-5 : General rule - Coating of test panel (brush application) 塗料一般試驗方法－第１－５部：通則－試驗板之塗裝（刷塗） |
|
|
|
CNS 8679
2019 Edition Method of Service Brake Road Test for Performance Requirements for Truck and Bus 貨車、大客車常用煞車─路段性能要求 |
|
|
|
CNS 14922
2019 Edition ESsential oils - Analysis by gas chromatography on packed columns - General method 精油－填充管柱氣相層析法通則 |
|
|
|
CNS 5345
2019 Edition Standard Definitions of Terms Relating to Adhesives 黏著劑有關名詞定義 |
|
|
|
CNS 3537
2019 Edition Planer KniveS for Woodworking Machines 建築物設計模矩 |
|
|
|
CNS 6369
2019 Edition Nylon Spun Yarns, Cotton System, Unfinished 尼龍紗（棉紡式，本白紗） |
|
|
|
CNS 15601
2019 Edition Commercial vehicleS − Obstacle detection device during reversing − Requirements and tests 商用車－倒車障礙物偵測裝置－要求與試驗 |
|
|
|
CNS 15161
2019 Edition Iron and Steel - Sampling and preparation of samples for the determination of chemical composition 鐵及鋼－化學成分定量分析用試樣之採取及製備 |
|
|
|
CNS 12013
2019 Edition Method of teSt for lead in gasoline by atomic absorption spectrometry 汽油鉛含量試驗法(原子吸收光譜法) |
|
|
|
CNS 15762-8
2019 Edition Footwear − TeSt methods for uppers − Part 8: Water resistance of uppers 鞋類－鞋面試驗法－第8 部：鞋面之耐水性 |
|
|
|
CNS 1467
2019 Edition Recording and Computing MethodS for Labor Injury 工作傷害記錄及計算方法 |
|
|
|
CNS 1170
2019 Edition Method of TeSt for Resistance of Concrete Specimens to Slow Freezing and Thawing in Water 混凝土試體抵抗凍融試驗法（水中緩慢凍融法） |
|
|
|
CNS 15711-2
2019 Edition Photovoltaic (PV) module performance teSting and energy rating − Part 2: Spectral responsivity, incidence angle and module operating temperature measurements 太陽光電模組性能試驗及能量定額－第2部：光譜響應度、入射角及模組操作溫度量測 |
|
|
|
CNS 14545-1
2019 Edition Fire hazard teSting-part 1:Guidance for assessing fire hazard of electrotechnical products(general guidance) 火災危險性試驗－第１部：評估電氣產品火災危險性的指引（通則） |
|
|
|
CNS 15166
2019 Edition Solar Energy - Field Pyranometers - Recommended practice for use 太陽能－場全天空輻射計－使用實務建議 |
|
|
|
CNS 5677
2019 Edition GloSsary of terms relating to cranes - Part 4: Mechanical parts of cranes 起重機詞彙－第４部：起重機之機械零組件 |
|
|
|
CNS 11341
2019 Edition Strip flooring 條狀地板 |
|
|
|
CNS 6694
2019 Edition Polyacrylonitrile Blended YarnS, Cotton System, Finished 聚丙烯月青混紡紗（梳毛式，漂染紗） |
|
|
|
CNS 1251
2019 Edition Canned tomato puree and paSte 番茄泥及番茄糊罐頭 |
|
|
|
CNS 4711
2019 Edition General ruleS of fixed resistors for use in electronic equipment 電子設備用固定電阻器通則 |
|
|
|
CNS 4620
2019 Edition Superior atmospheric corrosion resisting rolled steels 高耐候性軋鋼料 |
|
|
|
CNS 691
2019 Edition FluoreScent lamps (for general lighting service) 螢光燈管(一般照明用) |
|
|
|
CNS 14873-3
2019 Edition Road vehicleS - Airbag components - Part 3: Testing of inflator assemblies 道路車輛－氣囊組件－第３部：充氣器 |
|
|
|
CNS 8272
2019 Edition Bronze Globe ValveS for Marine Use (Union Bonnet Type) (5 kgf/㎠) 船用青銅管套帽型球形閥（5 kgf/㎠） |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [169] [170] [171] [172] [173] [174] [175] |
