"a, " CNS Standards List |
|
CNS 6695
2019 Edition Polyacrylonitrile Yarns, Worsted System, Finished 聚丙烯月青紗（梳毛式，本白紗） |
|
|
|
CNS 11670
2019 Edition Scaffolding plywood 施工架踏板用合板 |
|
|
|
CNS 4041
2019 Edition Chromium Molybdenum Steel Forgings for General Use 鉻鉬鋼鍛鋼件 |
|
|
|
CNS 15112
2019 Edition Method of test for determination of olefin content of gasolines by supercritical-fluid chromatography 汽油烯烴含量測定法（超臨界流體層析法） |
|
|
|
CNS 14545-5
2019 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 1:Glow-wire end-product test and guidance 火災危險性試驗－第２部：試驗方法－第１章／第１單元：完成品之熾熱線試驗及指引 |
|
|
|
CNS 6386
2019 Edition Nylon Blended Spun Yarns, Cotton System, Finished 尼龍混紡紗（棉紡式，漂染紗） |
|
|
|
CNS 13306-1-4
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Ancillary equipment - Radiated disturbances 射頻擾動和免疫力量測設備與量測方法－第１－４部：射頻擾動和免疫力量測設備－輔助設備－輻射擾動 |
|
|
|
CNS 3012
2019 Edition Rivets of Brake Linings and Clutch Facings for Automobiles 汽車煞車襯及離合器摩擦片用鉚釘 |
|
|
|
CNS 15063
2019 Edition Test method for determination of free formaldehyde in emulsion polymers by liquid chromatography 乳化聚合物游離甲醛液相層析測定法 |
|
|
|
CNS 9596
2019 Edition Method of Test of Strength for Automobile Suspension Springs 汽車用懸吊彈簧強度檢驗法 |
|
|
|
CNS 13520
2019 Edition Aluminium alloys used as galvanic anodes for cathodic protection 陰極保護用鋁合金犧牲陽極 |
|
|
|
CNS 61400-25-1
2019 Edition Wind energy generation systems − Part 25-1: Communications for monitoring and control of wind power plants − Overall description of principles and models 風力機－第25-1部：風力發電廠監控通訊－原理及模型整體描述 |
|
|
|
CNS 15030-26
2019 Edition Classification and labelling of chemicals - Aspiration hazard 化學品分類及標示－吸入性危害物質 |
Translated |
|
|
CNS 8237
2019 Edition Mounting Method of Brake Line and Electrical Connectors Between Truck Tractors and Trailers 貨車牽引車及拖車間剎車連結器及電線連接器之裝置方法 |
|
|
|
CNS 3211
2019 Edition Piping for Liquefied Petroleum Gas 汽車發動機活塞 |
|
|
|
CNS 13976
2019 Edition Method of test for flexural strength of dimensional stone 石材彎曲強度試驗法 |
|
|
|
CNS 15228-7
2019 Edition Test methods for lead-free solders - Part 7: Shear strength of solder joints on surface-mounted devices 無鉛銲錫試驗法－第７部：表面黏著元件上銲錫接點之剪力強度試驗法 |
|
|
|
CNS 13984
2019 Edition Methods of test for thermal diffusivity,specific heat capacity,and thermal conductivity of fine ceramics by laser flash method 精密陶瓷依雷射閃光法之熱擴散率、比熱容量、熱傳導率試驗法 |
|
|
|
CNS 62282-7-2
2019 Edition Fuel cell technologies − Part 7-2: Test methods − Single cell and stack performance tests for solid oxide fuel cells (SOFC) 燃料電池技術－第7-2部：試驗方法－固態氧化物燃料電池(SOFC)單電池及電池組性能試驗 |
|
|
|
CNS 15187-3-1
2019 Edition Low-voltage fuses - Part 3-1: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) - SectionsⅠto IV: Examples of types of standardized fuses 低壓熔線－第３－１部︰非專業人員用熔線之補充規定（以家用及類似用途為主之熔線）－第Ｉ章至第ＩＶ章：經標準化之熔線各種類型範例 |
|
|
|
CNS 5782
2019 Edition Cigarette Lighters for Automobiles 汽車用點煙器 |
Translated |
|
|
CNS 3489
2019 Edition Polyacrylonitrile Spun Yarns, Cotton System, Unfinished Regular Yarn 聚丙烯腈棉狀纖維（非收縮型） |
Translated |
|
|
CNS 20349-1
2019 Edition Personal protective equipment − Footwear protecting against risks in foundries and welding − Part 1: Requirements and test methods for protection against risks in foundries 個人防護具－防止鑄造及熔接中風險之鞋類－第1部：防護鑄造中風險之要求事項及試驗方法 |
|
|
|
CNS 8700
2019 Edition Quenched and Tempered Alloy Steel Forgings for Pressure Vessels 壓力容器用淬火–回火合金鋼鍛鋼件 |
|
|
|
CNS 8272
2019 Edition Bronze Globe Valves for Marine Use (Union Bonnet Type) (5 kgf/㎠) 船用青銅管套帽型球形閥（5 kgf/㎠） |
|
|
|
CNS 15748-1
2019 Edition Integrated circuits − Measurement of electromagnetic emissions, 150 kHz to 1 GHz − Part 1: General conditions and definitions 積體電路－150 kHz 至1 GHz 電磁放射量測－第1 部：一般條件及定義 |
|
|
|
CNS 13059-7
2019 Edition Photovoltaic devices - Part 7: Computation of the spectral mismatch correction for measurements of photovoltaic devices 太陽光電裝置－第7部：太陽光電裝置量測之光譜不匹配修正計算 |
|
|
|
CNS 13500
2019 Edition Method of Test for Grains - Moisture Contents of Cereals 穀類檢驗法–禾穀水分 |
Translated |
|
|
CNS 3102
2019 Edition Sleeve Type Half Bearing for the Crankshaft of Automobile Engines 汽車引擎用套筒型半分軸承 |
Translated |
|
|
CNS 16097-2
2019 Edition Machine tools − Dimensions and geometric tests for self-centring chucks with two-piece jaws − Part 2: Power-operated chucks with tongue and groove type jaws 工具機－具兩件式夾爪之自定心夾頭的尺度及幾何試驗－第2部：具榫槽式夾爪之動力操作夾頭 |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [158] [159] [160] [161] [162] [163] [164] |
