"7 " CNS Standards List| Petroleum products | Method Test | Single Coil | B ISDN | Inspection Amusement | Rubber compounding | Technical Terms | Audio visual, | |
|
CNS 4730
1984 Edition Lifting Eye Nuts 圓形環首螺帽 |
|
|
|
CNS 4733
1984 Edition Hexagon Nuts with Collar 突緣六角螺帽 |
|
|
|
CNS 10795
1984 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計（發電機式） |
|
|
|
CNS 6777
1984 Edition Indoor Post Insulators 屋內柱形絕緣體 |
|
|
|
CNS 2227
1984 Edition Low-Voltage Cartridge Fuses 低壓配線用筒型熔線 |
Translated |
|
|
CNS 6407
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 10786
1984 Edition Test Code for Performance of Drum Sanders 圓筒砂光機動態檢驗法 |
|
|
|
CNS 4732
1984 Edition Knurled Nuts with Ring 有環滾紋螺帽 |
|
|
|
CNS 10734
1984 Edition Method of Test for the Plastic Rims of Bicycle 平車或跑車型自行車塑膠輪圈檢驗法 |
|
|
|
CNS 11072
1984 Edition Method of X-Ray Fluorescence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 4731
1984 Edition Knurled Nuts for Drawing Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 11157
1984 Edition Lubrication Holes, Grooves and Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 1307
1984 Edition A. C. Watt-Hour Meter 交流瓦時計 |
Translated |
|
|
CNS 11087
1984 Edition Putty Knives 油灰刀 |
|
|
|
CNS 172
1983 Edition Woodruff Keys 半圓鍵 |
|
|
|
CNS 173
1983 Edition Key Section and Tolerance (Cold Drawing) 鍵鋼剖面及偏差（冷拉） |
|
|
|
CNS 4377
1983 Edition Square Thin Nuts 方螺帽（低型） |
|
|
|
CNS 4037
1983 Edition Parallel Bench Vices 鉗工虎鉗（方膛定座式） |
Translated |
|
|
CNS 4647
1983 Edition Square Taper Washers for High Prestressed Channels 斜墊圈（槽鐵高強度結構用） |
|
|
|
CNS 4607
1983 Edition Studs for T-Nuts 螺樁（Ｔ形螺帽用） |
|
|
|
CNS 4579
1983 Edition Bolted Connections with Reduced Body; Bolts 減徑柄螺栓之結合法（螺栓） |
|
|
|
CNS 171
1983 Edition Screw and Hole for Sliding Key 滑鍵螺釘及孔 |
|
|
|
CNS 4067
1983 Edition Square Nuts 方螺帽 |
|
| Find out:5135Items | To Page of: First -Previous-Next -Last | [158] [159] [160] [161] [162] [163] [164] |
