"1 " CNS Standards List |
|
CNS 11428
2018 Edition Watt-hour meter 瓦時計 |
Translated |
|
|
CNS 15499-3
2018 Edition Electrically propelled road vehicles – Safety specifications – Part 3: Protection of persons against electric shock 電動推進道路車輛－安全規範－第3部:預防人員電擊之保護 |
|
|
|
CNS 1382
2018 Edition Method of Test for Formaldehyde of Industrial Grade 工業級甲醛檢驗法 |
|
|
|
CNS 14952-1
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials - Part 1: General guidelines for ageing procedure and evaluation of test results 電氣絕緣材料之耐熱性測定指引－第１部：老化程序與試驗結果評估之一般導引 |
|
|
|
CNS 10062
2018 Edition Nominal Dimension of Veneer Jointers 薄板刨邊機之標稱尺度 |
|
|
|
CNS 12737
2018 Edition Spiral Steel Forms for Hollow Slab 中空樓板用螺旋鋼製管模 |
Translated |
|
|
CNS 12397
2018 Edition Signal Quality for Transmitting and Receiving Data Processing Terminal Equipments Using Serial Data Transmission at the Interface with Non-Synchronous Data Circuit-Terminating Equipment 發送及接收資料處理終端設備與非同步資料電路終端設備介面串列資料傳輸之信號品質 |
|
|
|
CNS 14545-6
2018 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 2:Glow-wire flammability test on materials 火災危險性試驗－第２部：試驗方法－第１章／第２單元：材料可燃性之熾熱線試驗 |
|
|
|
CNS 9561
2018 Edition Round-steel link chains for lifting - Grade 8 起重設備用圓鋼製環鏈－品質等級８ |
|
|
|
CNS 14393-1
2018 Edition Biological evaluation of medical devices – Part 1：Evaluation and testing 醫療器材生物性評估－第一部分：評估與試驗 |
|
|
|
CNS 12050
2018 Edition Heat resistant glass wares 耐熱玻璃製食品器具 |
|
|
|
CNS 1354
2018 Edition Methed of test for tensile properties of paper and board (Pendulum mehod) 紙及紙板抗張性質試驗法（擺錘法） |
|
|
|
CNS 15609-1
2018 Edition Thermoplastics pipes and fittings − Vicat softening temperature − Part 1: General test method 熱塑性塑膠管與管件－衛氏軟化 溫度－第1部：一般試驗法 , |
|
|
|
CNS 1366
2018 Edition Tinned Hard-drawn Single Solid Copper Wire 鍍錫硬銅單電線 |
Translated |
|
|
CNS 14202
2018 Edition Transmission of non-telephone signals - A far end camera control protocol for videoconference using H.224 非電話信號之傳輸–使用 CNS 14153 標準視訊會議的遠端攝影機控制協定 |
|
|
|
CNS 14327-1
2018 Edition Digital subscriber signalling system no.2-Connection modification:Peak cell rate modification by the connection owner 第二號數位用戶信號系統－連接修改：由連接擁有者從事之尖峰細胞速率修改 |
|
|
|
CNS 14952-3-2
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials – Part 3: Instructions for calculating thermal endurance characteristics – section 2: the calculation for incomplete data – verification for test result from gr 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第２章：不完整資料的計算－以包含中間時間到終止點之等量試驗群組驗證試驗結果 |
|
|
|
CNS 12365
2018 Edition Alphanumeric Character Sets for Optical Recognition - Part II : Character Set OCR-B-Shapes and Dimensions of the Printed Image 光學辨識用文數字集–第二部，ＯＣＲ–Ｂ字集–印出影像之形狀與尺度 |
|
|
|
CNS 11794
2018 Edition Minimum Length Between the Cable Entrances and the Terminals of Electric Machinery and Equipment for Marine Use 船用電器電纜導入口與端子間之最小尺度 |
|
|
|
CNS 10243
2018 Edition Data Processing Vocabulary (Part 16: Information Theory) 資料處理詞彙（第１６部：資訊理論） |
|
|
|
CNS 8751
2018 Edition Polyolefin pipes for the conveyance of fluids − Determination of resistance to crack propagation − Test method for slow crack growth on notched pipes 聚烯羥類織袋用帶狀延伸紗 |
|
|
|
CNS 15568
2018 Edition Protecting Equipment and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 15145
2018 Edition Preparation of steel substrates before application of paints and related products-Surface roughness characteristics of blast-cleaned steel substrates (Method for the grading of surface profile of abrasive blast-cleaned steel-Comparator procedure) 調理肉品 |
|
|
|
CNS 14238
2018 Edition Quality management systems - Guidelines for configuration management 品質管理系統－形態管理指導綱要 |
|
|
|
CNS 5341
2018 Edition Determination of density for vulcanized or thermoplastic rubber 硫化橡膠或熱塑性橡膠密度測定法 |
|
|
|
CNS 15593-46
2018 Edition Electricity metering − Data exchange for meter reading, tariff and load control – Part 46: Data link layer using HDLC protocol 電力計量－讀表、計費及負載控制之資料交換－第46部：使用HDLC協定之資料鏈路層 |
|
|
|
CNS 15153
2018 Edition Biological evaluation of medicaldevices - Part 17 : Establishment of allowable limits for leachable substances 醫療器材生物性評估－第１７部：可溶出物質容忍限量之建立 |
|
|
|
CNS 12451
2018 Edition Methods for Measuring Specific Gravity of Solid 固體比重測定法 |
|
|
|
CNS 1
2018 Edition Prevailing torque type hexagon regular nuts (with non-metallic insert) − Property classes 5, 8 and 10 等比標準數 |
|
|
|
CNS 17050-1
2018 Edition Conformity assessment − Supplier's declaration of conformity − Part 1: General requirements 符合性評鑑－供應者之符合性聲明－第1 部：一般要求事項 |
|
| Find out:10860Items | To Page of: First -Previous-Next -Last | [157] [158] [159] [160] [161] [162] [163] |
