"LE " CNS Standards List| Methods determination | 60° Center | Method test | Hexylene Glycol | Method Test | Method Test | Handles Cranes | Method Determination | |
|
CNS 9791
2017 Edition BeltLEd flange for pressure vessels 壓力容器螺栓之固定凸緣 |
|
|
|
CNS 12416
2017 Edition General ruLEs for atomic emission spectrometry 原子發光光譜分析通則 |
|
|
|
CNS 4952
2017 Edition Measurement Methods of Receiving Antenna for VHF TeLEvision Broadcast Transmissions ＶＨＦ電視機接收天線檢驗法 |
Translated |
|
|
CNS 8217
2017 Edition Method of Test for Low Frequency (Below 3 MHz) ELEctrical Connectors (TP - 27 Mechanical Shock Specified Pulse) 頻率３ＭＨｚ以下電連接器檢驗法（特定脈衝機械衝擊試驗ＴＰ–２７） |
|
|
|
CNS 7002
2017 Edition Machine Taper Pin Reamers with ParalLEl Shanks 推拔銷鉸刀（圓柱柄，機用） |
|
|
|
CNS 5183
2017 Edition ToLErance on Sewing Machine Parts for Home Use 家庭用縫紉機零件公差 |
|
|
|
CNS 5188
2017 Edition ShuttLE Raceing Slides of Sewing Machines for Home Use 家庭用縫紉機滑板 |
|
|
|
CNS 7254
2017 Edition Method of Test for Acetone ToLErance of Heat - Bodied Drying Oils 熟煉乾性油丙酮容許度測定法 |
|
|
|
CNS 15481-2
2017 Edition Road vehicLEs - Environmental conditions and testing for electrical and electronic equipment - Part 2: Electrical loads 道路車輛－電機電子配備環境條件與試驗－第２部：電力負載 |
|
|
|
CNS 2470
2017 Edition Testing Standard for Hanging and TabLE Clocks (Middle and High Grade) 中級及高級掛鐘及桌鐘檢驗標準 |
|
|
|
CNS 13991
2017 Edition Fixed resistor networks with individually measurabLE resistors for use in electronic equipment 電子設備用可單獨量測個別電阻元件之固定網路電阻器 |
|
|
|
CNS 13982-12
2017 Edition Methods of test for bulk down and feather − Part 12: Determination of average feather LEngth 羽絨羽毛試驗法－第12部：平均羽毛長度測定法 |
|
|
|
CNS 10697
2017 Edition Method of Test for Land MobiLE Communication FM or PM Receivers, 25-947 MHz (Radiated, Conducted Spurious Emission and Audio Squelch Sensitivity) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（輻射性、傳導性混附發射及聲頻靜音靈敏度） |
|
|
|
CNS 14466-16
2017 Edition Audiovisual,video and teLEvision equipment and systems. Part16:Labelling for educational audio cassettes 視聽．影像及電視設備與系統-第１６部：教育用聲音卡式磁帶之標籤 |
|
|
|
CNS 4152
2017 Edition Valve for Dissolved AcetyLEne Cylinder 溶解乙炔氣鋼瓶閥 |
Translated |
|
|
CNS 3510
2017 Edition Copper and copper alloy covered eLEctrodes 銅及銅合金被覆銲條 |
|
|
|
CNS 13811
2017 Edition Numerical-Type RefLEctors for Light Emitting Diodes 發光二極體數字型反射套板 |
|
|
|
CNS 15551-4
2017 Edition Ergonomics - AccessibLE design - Tactile dots and bars on consumer products 人因工程－無障礙設計 - 消費產品之觸覺點及觸覺條 |
|
|
|
CNS 11509
2017 Edition EdibLE goat milk powder 食用全脂羊乳粉 |
|
|
|
CNS 14717
2017 Edition Method for calculation of physical properties of liquefied petroLEum gases from compositional analysis 液化石油氣物理性質成分分析計算法 |
|
|
|
CNS 4745
2017 Edition Copper rod drawing stock for eLEctrical purposes 電氣用抽製銅條 |
|
|
|
CNS 12076
2017 Edition Die Wear ToLErance for Hot Forging Closed Die 熱鍛閉合模之模具磨耗許可量 |
|
|
|
CNS 9236
2017 Edition Method of Test for Low Frequency (Below 3 MHz) ELEctrical Connectors (TP - 2 Air Leakage) 頻率３ＭＨｚ以下電連接器檢驗法（漏氣試驗ＴＰ–２） |
|
|
|
CNS 9229
2017 Edition Method of Test for Dry Reed Switches (LEad Finish and Terminal Strength) 乾式簧開關檢驗法（引線表面處理與端子強度） |
|
|
|
CNS 1190
2017 Edition Half-round FiLE for Carpenter, Thin Sharp End 木工用細尖頭扁圓銼 |
Translated |
|
|
CNS 15700-1
2017 Edition Plugs, socket-outLEts, vehicle connectors and vehicle inlets − Conductive charging of electric vehicles − Part 1: General requirements 電源端插頭、電源端插座、車輛端插頭及車輛端插座－電動車輛傳導式充電－第1部：一般要求 |
|
|
|
CNS 10734
2017 Edition Method of Test for the Plastic Rims of BicycLE 平車或跑車型自行車塑膠輪圈檢驗法 |
|
|
|
CNS 135
2017 Edition Assembly tools for screws and nuts - DoubLE-headed open-ended engineer's wrenches 螺釘及螺帽之裝配工具－雙頭開口扳手(C級扭矩) |
|
|
|
CNS 1210
2017 Edition Mill Saw FiLE, Thin Type 薄形磨鋸銼 |
|
|
|
CNS 1254
2017 Edition Canned pickLEd vegetables 醬菜類罐頭 |
|
| Find out:6143Items | To Page of: First -Previous-Next -Last | [144] [145] [146] [147] [148] [149] [150] |
