"f " CNS Standards List |
|
CNS 15200-9-2
2019 Edition Methods of test for paints – Part 9-2: Coating powders – Inclined-plane flow test 塗料一般試驗法－第9-2 部：粉體塗料－斜面流動性試驗 |
|
|
|
CNS 4061
2019 Edition Reinforced Concrete Ditches (U Type) 鋼筋混凝土Ｕ形溝 |
Translated |
|
|
CNS 4711
2019 Edition General rules of fixed resistors for use in electronic equipment 電子設備用固定電阻器通則 |
|
|
|
CNS 1163
2019 Edition Method of test for bulk density and voids in aggregate 粒料容積密度與空隙率試驗法 |
|
|
|
CNS 14622-2
2019 Edition Sterilization of health care products − Biological indicators − Part 2: Biological indicators for ethylene oxide sterilization processes 健康照護產品滅菌－生物指示劑－第2 部：環氧乙烷滅菌程序之生物指示劑 |
|
|
|
CNS 20349-1
2019 Edition Personal protective equipment − footwear protecting against risks in foundries and welding − Part 1: Requirements and test methods for protection against risks in foundries 個人防護具－防止鑄造及熔接中風險之鞋類－第1部：防護鑄造中風險之要求事項及試驗方法 |
|
|
|
CNS 15615
2019 Edition Information technology − Telecommunications and information exchange between systems − Near Field Communication Interface and Protocol - 2 (NFCIP - 2) 資訊技術－系統間電信與資訊 交換－近場通訊介面與協定-2(NFCIP-2) |
|
|
|
CNS 15464
2019 Edition Concrete pipes for sewerage (Use for long length or turnable jacking method) 長距離、曲線推進用鋼筋混凝土管 |
|
|
|
CNS 15755-5-4
2019 Edition Conversion tables for units − Part 5-4: Pressure or stress − Millimeter of mercury and millibar 單位換算表－第5-4 部：壓力或應力－毫米汞柱與毫巴 |
|
|
|
CNS 15077-4
2019 Edition Test conditions for machining centers - Part 4 : Accuracy and repeatability of positioning of linear and rotary axes 切削中心機之檢驗條件－第４部：線性軸與旋轉軸之定位精度與重現性 |
|
|
|
CNS 10314
2019 Edition 600 V Grade polyethylene insulated wires for electrical apparatus 電機器具用600 V 聚乙烯絕緣電線 |
|
|
|
CNS 7270
2019 Edition Method of Test for Vinylon Ropes 維尼龍繩索檢驗法 |
|
|
|
CNS 15062
2019 Edition Paints and varnishes - Testing of formaldehyde-emitting coatings and melamine foams - Determination of the steady-state concentration of formaldehyde in a small test chamber 塗料－逸散甲醛塗膜與三聚氰胺泡棉試驗法－小型容器中恒定狀態甲醛濃度之測定 |
|
|
|
CNS 15685
2019 Edition Method of test for grain size of coated abrasive microgrits (P240-P2500) 砂紙、砂布用細粒磨料粒度試驗法 |
|
|
|
CNS 14934-5
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 5: Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16A 電磁相容－限制值－第5部：額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
|
|
|
CNS 15280
2019 Edition Standard test method for tension and elongation of elastic fabrics (constant-rate-of-extension type tensile testing machine) 彈性織物張力與伸度試驗法（定速伸長型試驗機） |
|
|
|
CNS 13306-1-1
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus 射頻擾動和免疫力量測設備與量測方法－第１－１部：射頻擾動和免疫力量測設備－量測設備 |
|
|
|
CNS 4829
2019 Edition Dropping Test for Electroplated Coatings of Zinc 鋅電鍍層滴定式厚度測定法 |
|
|
|
CNS 4063
2019 Edition Reinforced Concrete Covers for Ditches (U Type) 鋼筋混凝土Ｕ形溝用蓋 |
Translated |
|
|
CNS 15562-10
2019 Edition Stationary training equipment − Part 10: Exercise bicycles with a fixed wheel or without freewheel, additional specific safety requirements and test methods 固定式訓練器材－第10部：具固定輪或無自由輪健身車之附加特定安全要求與試驗法 |
|
|
|
CNS 15291
2019 Edition Safety of children’s clothing − Cords and drawstrings on children’s clothing − Specifications 兒童衣物安全規範－兒童衣物之繩帶與拉繩 |
|
|
|
CNS 14831
2019 Edition Method of test for oxygenates and paraffin , olefin , naphthene , aromatic（O-PONA）hydrocarbon types in low-olefin spark ignition engine fuels by gas chromatography 低烯烴汽油含氧化物、飽和烴、烯烴、環烷烴及芳香烴（O-PONA）測定法（氣相層析法） |
|
|
|
CNS 11013
2019 Edition Iron and steel－Methods for determination of silicon content 鐵及鋼－矽定量法 |
|
|
|
CNS 11206
2019 Edition Iron and steel─Methods for atomic absorption spectrometric analysis 鐵及鋼─原子吸收光譜分析法 |
|
|
|
CNS 15760-2
2019 Edition footwear − General test methods – Part 2: Sampling location, preparation and duration of conditioning of samples and test pieces 鞋類－ 一般試驗法－ 第2 部： 樣品與試片之取樣部位、製備及狀態調節時間 |
|
|
|
CNS 16107-2
2019 Edition Hollow taper interface with flange contact surface − Part 2: Receivers − Dimensions 具凸緣接觸面之空心錐度界面－第2部：接收器尺度 |
|
|
|
CNS 4349
2019 Edition Locks and Latches for Doors in Building 房屋用門鎖及閂鎖 |
Translated |
|
|
CNS 14900
2019 Edition Essential oils - General rules for packaging, conditioning and storage 精油－包裝材料、調節及儲存通則 |
|
|
|
CNS 15659-1
2019 Edition Evaluation of moisture-absorbing and quick-drying properties in textiles Part 1: Combination test 紡織品吸濕速乾性能評估－第1 部：組合試驗法 |
|
|
|
CNS 15876-7
2019 Edition Specification and qualification of welding procedures for metallic materials − Welding procedure test − Part 7: Overlay welding 金屬材料銲接程序規範書及其檢定－銲接程序試驗－第7部：堆銲 |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [118] [119] [120] [121] [122] [123] [124] |
