"5 " CNS Standards List |
|
CNS 14545-6
2018 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 2:Glow-wire flammability test on materials 火災危險性試驗－第２部：試驗方法－第１章／第２單元：材料可燃性之熾熱線試驗 |
|
|
|
CNS 15620-4
2018 Edition Insulation coordination for equipment within low-voltage system – Part 4: Considerationof high-frequency voltage stress 低電壓系統下設備之絕緣協調－第4 部：高頻電壓應力之考量 |
|
|
|
CNS 9492
2018 Edition Marine Bronze 5 kgf/㎠ Lift Check Angle Valves (Union Bonnet Type) 船用青銅管套帽型升程止回角閥（5 kgf/㎠） |
|
|
|
CNS 9599
2018 Edition Marine Floodlighting Projectors 船用投射燈 |
|
|
|
CNS 14952-1
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials - Part 1: General guidelines for ageing procedure and evaluation of test results 電氣絕緣材料之耐熱性測定指引－第１部：老化程序與試驗結果評估之一般導引 |
|
|
|
CNS 14151
2018 Edition Line transmission of non-telephone signals - Procedures for establishing communication between threeor more audiovisual terminals using digital channels up to 2Mbit/s 非電話信號之線傳輸–使用可達２Ｍｂｐｓ數位通道建立三部或以上視聽終端機間通訊之程序 |
|
|
|
CNS 15590-7
2018 Edition Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 9154
2018 Edition 660V, Twin-Core, Thre-Core EPR Insulated CP Sheathed Metal Netting Covered Cable and 660V Twin-Core, Three-Core EPR Insulated CP Sheathed Metal Netting Cover PVC Anti-Corrosion Cable for Marine Use 船用６６０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜（附各心線個別遮蔽）及６６０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附各心線個別遮蔽） |
|
|
|
CNS 10059
2018 Edition Nominal Dimensions of Glue Spreaders 佈膠機之標稱尺度 |
|
|
|
CNS 13598
2018 Edition Printing and writing paper（Uncoated wood–free paper） 印字色帶–容器上應出現的最少標示 |
|
|
|
CNS 13175
2018 Edition Method of Making Polyester Resin Concrete Specimens 聚酯樹脂混凝土強度試驗用試體製作法 |
Translated |
|
|
CNS 15710-3
2018 Edition Effects of current on human beings and livestock – Part 3: Effects of currents passing through the body of livestock 電流在人體及家畜上之效應－第3 部：電流通過家畜軀體之效應 |
|
|
|
CNS 7357
2018 Edition Polyvinyl formal enamelled rectangular copper winding wires 聚乙烯醇縮甲醛漆包鋁線 |
|
|
|
CNS 15568
2018 Edition Protecting Equipment and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 13715
2018 Edition Message Transfer Part (MTP) Signalling Preformance of Signalling System No.7 第七號信號系統訊息轉送部信號效能 |
|
|
|
CNS 15569-1
2018 Edition Hydraulic fluid power - Filter elements - Part 1: Verification of collapse/burst pressure rating 液壓流體動力－過濾器濾心－第1部：查證崩潰/爆裂壓力額定值 |
|
|
|
CNS 15620-3
2018 Edition Insulation coordination for equipment within low-voltage system – Part 3: Use of coating, potting or moulding for protection against pollution 低電壓系統下設備之絕緣協調－第3 部：用於污染防護之塗裝、封裝或壓塑 |
|
|
|
CNS 3376-5
2018 Edition Electrical apparatus of general use for explosive gas atmospheres-Part 5: Powder filling 〝q〞 爆炸性氣體環境用電機設備－第５部：填粉防爆構造〝ｑ〞 |
|
|
|
CNS 13540
2018 Edition Preblended dry mortar mix 預鑄混凝土電纜管組 |
|
|
|
CNS 8185
2018 Edition Method of Test for Building Components (Steel Panel for Wall) 建築用組件（鋼製牆壁嵌板）檢驗法 |
|
|
|
CNS 9559
2018 Edition Round-steel link chains for lifting - Grade 5 起重設備用圓鋼製環鏈－品質等級５ |
|
|
|
CNS 7225
2018 Edition Information Processing-Conventions for Incorporating Flowchart Symbols in Flowcharts 資訊處理–流程圖符號慣用法 |
|
|
|
CNS 15468-5-1
2018 Edition Fuel cell technologies - Part 5-1: Portable fuel cell power systems - Safety 燃料電池技術－第5-1部：可攜式燃料電池發電系統－安全 |
|
|
|
CNS 10135
2018 Edition Classification of Child-Resistant Packages 防止幼童開拆之包裝分類法 |
|
|
|
CNS 15676-3
2018 Edition Interior air of road vehicles − Part 3: Screening method for the determination of the emissions of volatile organic compounds from vehicle interior parts and materials − Micro-scale chamber method 道路車輛內部空氣－第3 部：車輛內部零件與材料之揮發性有機化合物逸散量篩檢測定法－微型試驗箱法 |
|
|
|
CNS 12451
2018 Edition Methods for Measuring Specific Gravity of Solid 固體比重測定法 |
|
|
|
CNS 11995
2018 Edition Spare Parts for Motor Starters and Controllers in Ships 船用電動機起動器及控制器之備品供給基準 |
|
|
|
CNS 5821
2018 Edition Determination of Resistance of Plastics to Colour Change Upon Exposure to Light of the Enclosed Carbon Arc 塑膠製品之抗變色性測定法（碳弧光法） |
|
|
|
CNS 5135
2018 Edition Method of Measurement for Applied Weight of Liquid Adhesives 液狀黏著劑之塗佈量測定法 |
|
|
|
CNS 15703-2
2018 Edition Tool shanks with 7/24 taper for automatic tool changers – Part 2: Dimensions and designation of shanks of forms J, JD and JF 自動換刀器用7/24 錐度刀柄－第2 部：刀柄型式J、JD 及JF 之尺度及標示 |
|
| Find out:6646Items | To Page of: First -Previous-Next -Last | [101] [102] [103] [104] [105] [106] [107] |
