"x " CNS Standards List |
|
CNS 60227-7
2020 Edition Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V − Part 6: Lift cables and cables for flexible connections 額定電壓450/750 V 以下聚氯乙烯絕緣電纜－第7部：兩心或多心遮蔽與無遮蔽可撓式電纜 |
|
|
|
CNS 15193-1
2020 Edition Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means of access between two levels 機械安全－接近機械之永久性方法－第１部：接近兩不同高度層固定方式之選擇 |
|
|
|
CNS 15353-2
2020 Edition Test methods for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Instrumental method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第２部：儀器測定法 |
|
|
|
CNS 8410-1
2020 Edition Test methods for corrosion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Alkali resistance test 鋁及鋁合金之陽極氧化膜耐蝕性試驗法－第１部：耐鹼性試驗法 |
|
|
|
CNS 15317-5
2020 Edition Crosslinked polyethylene (PE-x) pipe for hot and cold water conveyance - Part 5: Fitness for purpose of the system 冷熱水輸送用交連聚乙烯管─第５部：系統適合度 |
|
|
|
CNS 8410-2
2020 Edition Test methods for corrosion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 2: CASS test 鋁及鋁合金之陽極氧化膜耐蝕性試驗法－第２部：含銅加速醋酸鹽水噴霧試驗法 |
|
|
|
CNS 3-3
2020 Edition Engineering Drawing (Method of indicating surface texture on drawings) 工程製圖(表面織構符號) |
|
|
|
CNS 1863
2020 Edition Phosphorus Oxychloride 化學試藥（氧氯化磷） |
|
|
|
CNS 15355
2020 Edition Test method for determination of mass per unit area of anodic oxide coatings on aluminium and aluminium alloys -Gravimetric method 鋁及鋁合金之陽極氧化膜單位面積質量試驗法－重量分析法 |
|
|
|
CNS 1258
2020 Edition Method of Test for Autoclave Expansion of Portland Cement 卜特蘭水泥熱壓膨脹試驗法 |
|
|
|
CNS 60669-1
2020 Edition Switches for household and similar fixed electrical installations − Part 1: General requirements 家用和類似用途固定式電氣裝置之開關－第1部：一般要求 |
|
|
|
CNS 3655
2020 Edition Method for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency 水硬性水泥可塑稠性水泥漿及墁料之機械拌合法 |
|
|
|
CNS 15319-2
2020 Edition Sodium hydroxide for industrial use - Part 2: Determination of total alkalinity, sodium hydroxide and sodium carbonate 工業用氫氧化鈉－第２部：總鹼、氫氧化鈉及碳酸鈉測定法 |
|
|
|
CNS 15434
2020 Edition Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards 機械安全—防護裝置—設計與建構固定式和移動式防護裝置之一般要求 |
|
|
|
CNS 60669-2-1
2020 Edition Switches for household and similar fixed electrical installations − Part 2-1: Particular requirements − Electronic switches 家用和類似用途固定式電氣裝置之開關－第2-1 部：電子式開關之個別要求 |
|
|
|
CNS 153
2020 Edition Coarse Type Washers (Primarily for Hexagonal Bolts and Nuts) 粗製墊圈（用於六角螺釘及螺帽） |
Translated |
|
|
CNS 15353-1
2020 Edition Test methods for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart scale method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第１部：圖表比例尺法 |
|
|
|
CNS 1865
2020 Edition Phosphorus Pentoxide 化學試藥（五氧化二磷） |
|
|
|
CNS 14596
2020 Edition Welding consumables − Gas shielded and self-shielded flux cored wires for arc welding of mild steel, high strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用 鋼氣遮護及自遮護電弧銲接用包藥銲線 |
|
|
|
CNS 14964-6
2020 Edition Wheelchairs − Part 6: Determination of maximum speed of electrically powered wheelchairs 輪椅－第6部：電動輪椅最大速率之測定 |
|
|
|
CNS 9445-1
2020 Edition Sampling procedures for inspection by variables − Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL 計量值檢驗抽樣程序－第1部：單一品質特性與單一允收品質界限(AQL)逐批檢驗依AQL檢索之單次抽樣計畫 |
|
|
|
CNS 8411-2
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Abrasive jet test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－第２部：噴射磨耗試驗法 |
|
|
|
CNS 15354
2020 Edition Test methods for dielectric strength of anodic oxide coatings on aluminium and aluminium alloys 鋁及鋁合金之陽極氧化膜絕緣性試驗法 |
|
|
|
CNS 15356
2020 Edition Test method for continuity of anodic oxide coatings on aluminium and aluminium alloys - Copper sulphate test 鋁及鋁合金之陽極氧化膜連續性試驗法－硫酸銅試驗法 |
|
|
|
CNS 15692-3
2020 Edition Safety of machinery − Laser processing machines − Part 3: Noise reduction and noise measurement methods for laser processing machines and hand-held processing devices and associated auxiliary equipment (accuracy grade 2) 機械安全－雷射加工機－第3 部：雷射加工機、手持加工裝置及附屬輔助設備之噪音降低及噪音量測法(準確度等級2) |
|
|
|
CNS 7818
2020 Edition Chemical Reagent (Potassium Hexachloropatiate (IV)) 化學試藥（六氯鉑酸（ＩＶ）鉀） |
|
|
|
CNS 14145
2020 Edition Methods of test for measuring thermal expansion of fine ceramics by thermomechanical analysis 精密陶瓷以熱工分析之熱膨脹測定法 |
|
|
|
CNS 1891
2020 Edition Potassium hydroxide; solid 化學試藥（碘酸鉀） |
|
|
|
CNS 60669-2-6
2020 Edition Switches for household and similar fixed electrical installations – Part 2-6: Particular requirements – Fireman's switches for exterior and interior signs and luminaires 家用和類似用途固定式電氣裝置之開關－第2-6 部：外部與內部標誌及燈具用消防員開關之個別要求 |
|
|
|
CNS 15352
2020 Edition Hard anodic oxide coatings on aluminium and aluminium alloys 鋁及鋁合金之硬質陽極氧化膜 |
|
| Find out:1665Items | To Page of: First -Previous-Next -Last | [5] [6] [7] [8] [9] [10] [11] |
