"With " CNS Standards List |
|
CNS 4371
2017 Edition Round Thread With Clearance and Steep Flank with Pitch 7 mm Theoretic Values 圓螺紋（具有間隙、深螺腹、螺距為７ｍｍ之理論值） |
|
|
|
CNS 210
2017 Edition Short Drills With Square Taper Shank 方錐柄短鑽頭 |
Translated |
|
|
CNS 4228
2017 Edition Finishes With External Screw Thread for Glass Containers 玻璃容器用外螺紋 |
|
|
|
CNS 4321
2017 Edition Hexagon Bolts With Approximately to Head, Finished and Semi-Finished, Metric Fine Thread 六角頭全螺紋螺栓（精製及半精製，公制細螺紋） |
|
|
|
CNS 13982-8
2017 Edition Methods of test for bulk down and feather − Part 8: Determination of fill power With steam conditioning 羽絨羽毛試驗法－第8部：蒸汽處理後蓬鬆度測定法 |
|
|
|
CNS 7194
2017 Edition Single-start solid (monobloc) gear hobs With tenon drive or axial keyway, modules 1 to 40-Nominal dimensions 具有榫槽或鍵槽之單紋螺紋滾齒刀﹝模數１至４０﹞─標稱尺度 |
|
|
|
CNS 8473
2017 Edition Pin Allocations for Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use With Printed Boards 衝頭（打銷用） |
|
|
|
CNS 15235
2017 Edition Methods of accelerated cyclic corrosion resistance tests for anodic coatings With exposure to salt spray, dry and wet conditions 陽極被覆鋼板之加速循環腐蝕試驗法 |
|
|
|
CNS 13059-3
2017 Edition Photovoltaic Devices Part 3：Measurement Principles for Terrestrial Photovoltaic (PV) Solar Devices With Reference Spectral Irradiance Data 光電伏打元件（第三部：具光譜照射光參考數據之陸上光電伏打（ＰＶ）太陽元件量測原理） |
|
|
|
CNS 15233
2017 Edition Fixtures of roadway lighting With light emitting diode lamps 發光二極體道路照明燈具 |
Translated |
|
|
CNS 4692
2017 Edition Studs for Stud Welding With Tip Ignition; Unthreaded Studs 尖端燃熔用無螺紋樁 |
|
|
|
CNS 4580
2017 Edition Bolted Connections With Reduced Body; Studs 減徑柄螺栓之結合法（螺樁） |
|
|
|
CNS 5508
2017 Edition Rolling Bearings; Bearings With Spherical Outside Surface and Extended Inner Ring Width, Steel Pressed Housings for Insert Bearings 嵌入夾緊滾動軸承用壓製外殼 |
|
|
|
CNS 242
2017 Edition Machine Reamer, With Morse Taper Shank 機用鉸刀（莫氏圓錐柄） |
|
|
|
CNS 12880
2017 Edition Cement Sack Paper Laminated With Plastic Woven Sheet 塑膠編織貼合水泥袋紙 |
Translated |
|
|
CNS 4856
2017 Edition Fixed capacitors for use in electronic equipment (Aluminium electrolytic capacitors With solid and non-solid electrolyte) 電子設備用鋁質電解電容器（固體及非固體電解質） |
|
|
|
CNS 16009-7
2017 Edition Ladders − Part 7: Mobile ladders With platform 梯具－第7部：活動式工作平台梯 |
|
|
|
CNS 10683
2017 Edition Round Steel Chains Without Quality Requirements 圓鋼製環鏈（不涉及品質要求） |
|
|
|
CNS 9311
2017 Edition Method of test for colour fastness to carbonizing With sulphuric acid 耐硫酸碳化染色堅牢度試驗法 |
|
|
|
CNS 243
2017 Edition Machine Reamers With Insert Blades 嵌刃式機用鉸刀（莫氏圓錐柄） |
|
|
|
CNS 7001
2017 Edition Driving Tenons for Tools With Parallel Shank 驅動榫舌（圓柱柄，工具用） |
|
|
|
CNS 244
2017 Edition Adjustable Machine Reamer With Morse Taper Shank 機用活動鉸刀（莫氏圓錐柄） |
|
|
|
CNS 4481
2017 Edition Hexagon Socket Set Screws With Cone End 六角承窩無頭錐形端固定螺釘 |
|
|
|
CNS 15550
2017 Edition Guidelines for standards developers to address the needs of older persons and persons With disabilities 標準發展者考量年長者與 身心障礙者需求之指導綱要 |
|
|
|
CNS 257
2017 Edition Boiler Rivet Hole Reamer, With Square Head 鍋爐鉚釘孔鉸刀（方頭圓柱柄） |
|
|
|
CNS 11999
2017 Edition Structural Steels With Specified Hardenability Bands 保證硬化能構造用鋼料（Ｈ鋼） |
|
|
|
CNS 6879
2017 Edition Machine Taps With Reinforced Shank for Coarse ISO Metric Threads 螺絲攻（ＩＳＯ公制粗螺紋，加強柄、機用） |
|
|
|
CNS 4420
2017 Edition Countersunk Head Bolts With Forged Slot for Steel structures 鍛槽平頂埋頭螺栓（鋼結構用） |
|
|
|
CNS 4693
2017 Edition Fish Bolts With Round Head and Oval Neck 魚尾板螺栓（具圓頭橢圓頸） |
|
|
|
CNS 2251
2017 Edition Aluminium Foil Laminated With Paper Lining 褙紙鋁箔 |
|
| Find out:672Items | To Page of: First -Previous-Next -Last | [5] [6] [7] [8] [9] [10] [11] |
