"coarse" CNS Standards List| Information technology | Slotted Oval | Hospital Grade | Two Flute | Method calculated | Electric vehicle | Chemical Reagent | Wind turbines | |
|
CNS 490
2021 Edition Method of test for resistance to degradation of coarse aggregate (smaller then 37.5 mm) by abrasion and impact in the Los Angeles machine 粗粒料（37.5mm以下）洛杉磯磨損試驗法 |
|
|
|
CNS 486
2021 Edition Method of test for sieve analysis of fine and coarse aggregates 粗細粒料篩析法 |
|
|
|
CNS 5000
2021 Edition Ground Thread Taps for ISO Metric Threads of Tolerances 4H to 8H and 4G to coarse and Fine Pitches-Manufacturing Tolerances on the Threaded Portion 螺絲攻磨製螺紋公差（用於４Ｈ至８Ｈ及４Ｇ至６Ｇ之粗螺紋及細螺紋） |
|
|
|
CNS 15312
2021 Edition Method of test for determining the percentage of fractured particles in coarse aggregate 粗粒料中破碎顆粒含量試驗法 |
|
|
|
CNS 14732
2021 Edition Method of test for correction for coarse particles in the soil compaction 依粗料含量調整土壤夯實密度試驗法 |
|
|
|
CNS 533
2021 Edition Limit Gages for Metric coarse Screw Threads 公制粗螺紋限界量規 |
|
|
|
CNS 14779
2021 Edition Method of test for the particle cylindrical crushing strength of lightweight coarse aggregates 輕質粗粒料之顆粒筒壓強度試驗法 |
|
|
|
CNS 15308
2021 Edition Standard specification for coarse aggregate for bituminous paving mixtures 瀝青鋪面混合料用粗粒料 |
|
|
|
CNS 535
2021 Edition Limit Gages for Unified coarse Screw Threads 統一制粗螺紋限界量規 |
|
|
|
CNS 15313
2021 Edition Method of determining the adherent coating on coarse aggregates 測定粗粒料附著層之試驗法 |
|
|
|
CNS 4545
2020 Edition Limits of Sizes and Tolerances for ISO Metric coarse Screw Threads (Tolerance Quality: Coarse,Tolerances: 7H and 8g)(Diameters from 3 to 68mm and Pitches 0.5 to 6mm) 公制粗螺紋限界尺寸及公差（ISO制）（粗品級–7H、8g）（標稱直徑3至68mm，螺距0.5至6mm） |
|
|
|
CNS 520
2020 Edition Tolerance of Whitworth Threads (Medium and coarse Fits) 韋氏螺紋偏差及公差（中配及粗配） |
|
|
|
CNS 153
2020 Edition coarse Type Washers (Primarily for Hexagonal Bolts and Nuts) 粗製墊圈（用於六角螺釘及螺帽） |
Translated |
|
|
CNS 4548
2020 Edition Limits of Sizes and Tolerances for ISO Metric Fine Screw Threads (Tolerance Quality: coarse,Tolerances: 7H and 8g)(Diameters from 4 to 300mm and Pitches 0.5 to 6mm) 公制細螺紋限界尺寸及公差（ISO制）（粗品級–7H、8g）（標稱直徑4至300mm，螺距0.5至6mm） |
|
|
|
CNS 4544
2020 Edition Limits of sizes and tolerances for ISO metric coarse screw threads (Tolerance quality: medium, tolerances: 5 H、6 H and 6 h、6 g)(Diameters from 1 to 68 mm and pitches 0.25 to 6 mm) 公制粗螺紋限界尺寸及公差（ＩＳＯ制）（中品級–5Ｈ、6Ｈ、6ｈ、6ｇ）（標稱直徑1至68mm，螺距0.25至6mm） |
|
|
|
CNS 521
2020 Edition Limit of Whitworth Threads (Medium and coarse Fits) 韋氏螺紋限界尺寸（中配及粗配） |
|
|
|
CNS 532
2020 Edition Limits of Size and Tolerances for ISO Metric coarse Screw Threads (Tolerance Quality:Fine,Tolerances:4H、5H and 4h)(Diameters from 1 to 68 mm and Pitches 0.25 to 6 mm) 公制粗螺紋限界尺寸及公差（ISO制）（細品級–4H、5H、4h）（標稱直徑1至68mm，螺距0.25至6mm） |
|
|
|
CNS 497
2020 Edition ISO Metric coarse Screw Threads 公制粗螺紋（ＩＳＯ制） |
Translated |
|
|
CNS 488
2019 Edition Method of test for density, relative density (specific gravity), and absorption of coarse aggregate 粗粒料密度、相對密度（比重）及吸水率試驗法 |
|
|
|
CNS 15171
2019 Edition Method of test for flat particles, elongated particles, or flat and elongated particles contents in coarse aggregate 粗粒料中扁平、細長或扁長顆粒含量試驗法 |
|
|
|
CNS 15590-5
2019 Edition Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners with specified hardness classes – coarse thread and fine pitch thread 碳鋼及合金鋼結件之機械性質－第5 部：規定硬度級數之固定螺釘及類似螺紋結件－粗螺紋及細螺紋 |
|
|
|
CNS 11824
2019 Edition Air-cooled blast furnace slag coarse aggregate for concrete 混凝土用高爐爐 碴粗粒料 |
|
|
|
CNS 6362
2019 Edition Method of Test for coarse Particles in Pigments 顏料中粗粒檢驗法 |
|
|
|
CNS 3408
2019 Edition Method of Test for Resistance to Abrasion of Large Size coarse Aggregate by Use of the Los Angeles machine 粗粒料（粒徑１９ｍｍ以上）磨損試驗法 |
Translated |
|
|
CNS 1322
2018 Edition Plug Gauge for Whitworth Thread (No Go End Limit for Fine,Medium and coarse Fits) 鋼桶用口基及口蓋 |
|
|
|
CNS 6877
2017 Edition Hand Taps in Set of Three, for coarse ISO Metric Threads 螺絲攻（ＩＳＯ公制粗螺紋，三件成套，手用） |
|
|
|
CNS 6881
2017 Edition Machine Taps for coarse ISO Metric Threads 螺紋攻（ＩＳＯ公制粗螺紋、機用） |
|
|
|
CNS 527
2017 Edition Inspection Plug Gauge for Whitworth Thread Ring Gauge (Go End Limit for Fine, Medium and coarse Fits) 韋氏螺紋樣圈之量柱及損磨量柱（通過端，精配，中配及粗配） |
|
|
|
CNS 524
2017 Edition Plug Gauge for Whitworth Thread (Go End Limit for Fine, Medium and coarse Fits) 韋氏螺紋量柱（不通過端限界尺寸，精配，中配及粗配） |
|
|
|
CNS 528
2017 Edition Adjustable Plug Gauge for Whitworth Thread Ring Gauge (For Testing of Go and No Go Ring Gauge, Fine, Medium and coarse Fits) 韋氏螺紋活動量規（檢驗通過及不通過端樣圈，精配，中配及粗配） |
|
| Find out:54Items | To Page of: First -Previous-Next -Last | 1 2 |
